Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
38 BL26BC BL26C0 Fig. 35 Fig. 36 NOTE: SplitLine™ can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel. Use Figure 36 to identify the inner reel you have. BL26BC Fig. 40 BL26C0 MAINTENANCE AND REPAIR INSTRUCTIONS SplitLine™ Installation 8. Take approximately 8 feet (2.5 m) of new trimming line. Insert one end of the line through one of the two holes in the inner reel (Fig. 41 or 42). Pull the line through the inner reel until only about 4 inches is left out. 9. Insert the end of the line into the open hole in the inner reel and pull the line tight to make the loop as small as possible (Fig. 41 or 42). 10. Before winding, split the line back about 6 inches. 11. Wind the line in tight even layers in the direction indicated on the inner reel. NOTE: Failure to wind the line in the direction indicated will cause the cutting attachment to operate incorrectly. 12. Insert the ends of the line into the two holding slots (Fig. 43). BL26BC Loop Fig. 41 BL26C0 Loop Fig. 42 Holding Slots Fig. 43 13. Insert the ends of the line through the eyelets in the outer spool and place inner reel with spring inside the outer spool (Fig. 44 or 45). Push the inner reel and outer spool together. While holding the inner reel and outer spool, grasp the ends and pull firmly to release the line from the holding slots in the reel. NOTE: The spring must be assembled on the inner reel before reassembling the cutting attachment. 14. Hold the inner reel in place and install the bump knob by turning counterclockwise (BL26BC) or clockwise (BL26C0). Tighten securely. Spring BL26BC Fig. 44 BL26C0 Eyelet Spring Eyelet Fig. 45 Installing a Prewound Wheel 1. Hold the outer spool with one hand and unscrew the bump knob clockwise (BL26BC) or counterclockwise (BL26C0). Inspect the bolt inside the bump knob to make sure it moves freely. Replace the bump knob if damaged (Fig. 31 or 32). 2. Remove the old inner reel from the outer spool (Fig. 31 or 32). 3. Remove the spring from the old inner reel (Fig. 31 or 32). 4. Place the spring in the new inner reel. NOTE: The spring must be assembled on the inner reel before reassembling the cutting attachment. 5. Insert the ends of the line through the eyelets in the outer spool (Fig. 44 or 45). 6. Place the new inner reel inside the outer spool. Push the inner reel and outer spool together. While holding the inner reel and outer spool, grasp the ends and pull firmly to release the line from the holding slots in the spool. 7. Hold the inner reel in place and install the bump knob by turning counterclockwise (BL26BC) or clockwise (BL26C0). Tighten securely. 20 MAINTENANCE AND REPAIR INSTRUCTIONS Always use original equipment manufacturer ™ 0.080 inch (2.03 mm) replacement line. Lines other than those specified may make the engine overheat or fail. There are two methods to replace the SpeedSpool® trimming line: • Wind the inner reel with new line • Install a pre-wound inner reel Winding the Inner Reel With New Line NOTE: It Is unnecessary to remove the bump knob to install a new trimming line. 1. Cut two pieces of 0.080 inch (2.03 mm) trimming line, 10 feet (3 m) long. 2. Hold the outer spool and turn the inner reel counterclockwise to line up the arrows on the outer spool and inner reel (Fig. 46). Top View Of The SpeedSpool® Outer Spool Inner Reel Fig. 46 Bump Knob Arrows SPEEDSPOOL® (BL26SS) Never use metalreinforced line, wire, chain or rope. These can break off and become dangerous projectiles. WARNING: Always use the correct line length when installing trimming line on the unit. The line may not release properly if the line is too long. WARNING: Line Locking Hole Trimming Line Line Loading Hole Eyelet 5. Insert the line into the locking hole (Fig. 48). Do not push the line more than a 1/2 inch (12.7 mm) into the line locking hole. The line will form a small loop (Fig. 48) when it is inserted correctly. 3. Pull old line out of the line loading and line locking holes (Fig. 47 and 48). 4. Insert a piece of trimming line straight into one of the two eyelets in the outer spool. Push it up through the line loading hole in the inner reel (Fig. 47). Do not bend the line when inserting it into the eyelet. Fig. 47 Fig. 48 6. Pull the line from the outer spool until the line is tight against the inner reel (Fig. 49). Fig.49 21 MAINTENANCE AND REPAIR INSTRUCTIONS INSTALLING A PRE-WOUND REEL 1. Turn the bump knob counterclockwise and remove the bump knob, spring and foam seal (Fig. 52). 9. If winding the line becomes difficult or if the line jams, pull the ends of the line from the spool (Fig. 51). Continue winding the inner reel counterclockwise. Fig. 50 Fig. 51 7. Repeat procedures 4-6 with the second piece of line. 8. Hold the outer spool. Wind the inner reel counterclockwise until approximately four (4) inches (102 mm) of line remain (Fig. 50). NOTE: Do not wind the inner reel before installing the second piece of line. Bump Knob Foam Seal Spring Inner Reel Fi...