Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Place a few drops of Andis OIL Clipper Oil on the front and OIL side of the cutter blades (See Diagram B). Wipe excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper coolant. Always replace broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using a Diagram B small brush or worn out tooth brush. To clean the blades we suggest to immerse the blades only into a shallow pan of Andis Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After cleaning, turn your clipper/trimmer off and dry blades with a dry cloth and start clipping again. REPLACEMENT (REMOVAL) OF BLADE SET Your Andis clipper/trimmer consists of a preset tension assembly on the blade set. To remove blade set from your clipper/trimmer, remove from charger base. Turn the clipper/trimmer upside down so teeth of blades Diagram CSTAINLESS ® BLADE SCREWSare facing down. You may wish to set the clipper on a flat surface while performing these operations. Using a phillips type screwdriver, unscrew the two blade screws as shown in Diagram C. Remove blade set from clipper/trimmer. Install new blade set, making sure the blade yoke cradles the armature pin on clipper/trimmer (See Diagram D). There is no need to adjust blade tension before use, as tension has been preset at the factory. Align screw holes of blade set to screw inserts on clipper/trimmer housing. Replace the screws. Before tightening down blade screws, check alignment of blade set to housing, making sure that they are parallel. Tighten down screws. ARMATURE PIN BLADE YOKE Diagram D Attaching The Clipper Combs (Some models do not have attachment combs) The clipper comb blade attachments mount easily. Just snap them on. Snap them off. Combs help guide hair to cutting blades and give you precise control of hair lengths. Each comb allows a different length of cut which is indicated on the combs: 1/16", 1/8", 1/4", and 3/8". You can always set blades for a coarser cut by attaching any of the four snap-on blade attachments. To use a blade attachment, slip the cutter blade teeth into blade attachment. Snap blade attachment down, they snap on and off easily. These attachments guide hair into the clipper blades and give you precise control of hair lengths. The length of trim is indicated on the blade attachment: 1/16", 1/8", 1/4", and 3/8". Use the following chart to find the approximate lengths of cut. Different blade angles in relation to the skin, thickness and texture of the hair will vary the cutting length. CLIPPING GUIDE Description Clipping Direction Approx. Length of Cut Standard Andis Blade With hair grain Against hair grain 1/16" 1/32" 1/16" Blade Attachment #1 With hair grain Against hair grain 3/16" 3/32" 1/8" Blade Attachment #1 1/2 With hair grain Against hair grain 1/4" 1/8" 1/4" Blade Attachment #2 With hair grain Against hair grain 3/8" 1/4" 3/8" Blade Attachment #3 1/2 With hair grain Against hair grain 1/2" 3/8" The Preliminaries 1. To make cutting smoother and easier, always start with a clean head of hair. Wash the hair with your favorite shampoo. Rinse. Repeat. We also recommend using a hair conditioner to untangle snarls and leave hair soft and easy to manage. 2. When drying the hair, just use a towel so as not to dry it too thoroughly. Leaving it damp makes the hair easier to work with. FACTORY REPAIR SERVICE When the blades of your Andis clipper/trimmer become dull after repeated use, it is advised to purchase a new set of blades available through your Andis Supplier or through an Andis Authorized Repair Station listed in this manual. If you wish your clipper/trimmer to be serviced as well, it should be carefully packed and mailed either Parcel Post Insured, or U.P.S. to any of the Service Centers listed in manual. ANDIS AUTHORIZED REPAIR STATIONS RYAN’S SHARPENING 1805 E. McDowell Rd., Phoenix, AZ 85006-0352 GROOM-IT INDUSTRIES 3305 Glendale Blvd., Los Angeles, CA 90039 GROOMTECH/LPS 555 Saturn Blvd, #436, San Diego, CA 92154 APPLIANCE SALES & SERV. 840 Folsom St., San Francisco, CA 94105 THE SHAVER SHOP 17516 Hawthorne Blvd., Torrance, CA 90504 MILBERN’S 2434 N. Federal Hwy., Lighthouse Point, FL 33064 954-941-3213 C.J.’S GROOMING TOOLS 3241 Shallowford Rd., Atlanta, GA 30341 K.A. VOGEL & SONS, INC. 2215 N. Milwaukee Ave., Chicago, IL 60647 AUTHORIZED SERVICE CO. 1644 W. Ogden Ave., Downers Grove, IL 60515 STEPHENSON’S SALES & SERVICE 156 E. Main St., Lake Zurich, IL 60047 LAVILLE SERVICE & SUPPLY 419 West Ewing Ave., South Bend, IN 46613 SCOTLAND YARD 8432 Quail, Florence, KY 41042 SMALL APPLIANCE REPAIR 2636 Jefferson Highway, Jefferson, LA 70121 WATERS APPLIANCE SERVICE 216 E. Diamond Ave., Gaithersburg, MD 20877 BO-JO CLIPPER SERVICE 615 Summer St., Lynn, MA 01905 SHAVER & TIME WORLD 27326 Grand River Rd., Redford, MI 48240 SUPERIOR APPLIANCE SERV. 1050 Scribner N.W., Grand Rapi...