Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Warning Your shaving system is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. This appliance is not intended for use by children or persons with reduced physical or mental capabilities, unless they are supervised by a person responsible for their safety. In general, we recommend that you keep the appliance out of reach of children. Children should be supervised to ensure that they do not play with the appliance. To prevent the cleaning fl uid from leaking, ensure that the Clean&Renew station is placed on a fl at surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fl uid might spill out of the cartridge. Do not place the station inside a mirror cabinet, nor over a radiator, nor place it on a polished or lacquered surface. The cleaning cartridge contains a highly fl ammable liquid so keep it away from sources of ignition. Do not smoke near the station. Do not expose to direct sunlight for long periods of time. Do not refi ll the cartridge and use only original Braun refi ll cartridges. Oil bottle Keep out of reach of children. Do not swallow. Dispose of properly when empty. Description Clean&Renew station 1 Cleaning fl uid display 2 Lift button for cartridge exchange 3 Station-to-shaver contacts 4 Start button 5 Cleaning program indicators 6 Station power socket 7 Cleaning cartridge Shaver 8 Foil & Cutter cassette 9 Cassette release button STOP 25 0 Shaver head «lock» switch q Pop-out long hair trimmer w On/off switch e (–) setting button (sensitive) r (+) setting button (intensive) t Reset button z Shaver display u Shaver-to-station contacts i Shaver power socket o Travel case p Special cord set Before shaving Prior to fi rst use you must connect the shaver to an electrical outlet using the special cord set p or alternatively proceed as below. Installing the Clean&Renew station • Using the special cord set p, connect the station power socket 6 to an electrical outlet. • Press the lift button 2 to open the housing. • Hold the cleaning cartridge 7 down on a fl at, stable surface (e.g. table). • Carefully remove the lid from the cartridge. • Slide the cartridge into the base of the station as far as it will go. • Slowly close the housing by pushing it down until it locks. The cleaning fl uid display 1 will show how much fl uid is in the cartridge: up to 30 cleaning cycles available up to 7 cleaning cycles remaining new cartridge required Charging and cleaning the shaver Insert the shaver head down into the cleaning station. (The contacts u on the back of the shaver will align with the contacts 3 in the cleaning station). If required, the Clean&Renew station will automatically charge the shaver. The hygiene status of the shaver will also be analyzed and one of the following cleaning program indicators 5 will light up: new fast clean fast clean 2 1 t r im m er seireS 7 26 « » shaver is clean « » short economical cleaning required « » normal level of cleaning required « » high intensive cleaning required If the station selects one of the required cleaning programs, it will not start unless you press the start button 4. For best shaving results, we recommend cleaning after each shave. Each cleaning program consists of several cycles, where cleaning fl uid is fl ushed through the shaver head. Depending on the program selected, the cleaning time takes 3 to 15 minutes and drying takes about 4 hours. During this time the respective indicator blinks. The cleaning program should not be interrupted. Whilst the shaver is drying, the shaving head may be wet. When the program is fi nished, the blue « » indicator will light up. Your shaver is now clean and ready for use. Stand-by mode 10 minutes after completing the charging or cleaning session, the Clean&Renew station switches to the stand-by mode: The indicators of the Clean&Renew station turn off. Shaver display The shaver display z shows the charge status of the battery. During charging or when using the shaver, the respective green charge status will blink. When the battery is fully charged the green charge status will light up continously, provided the shaver is connected to an electrical outlet. Stand-by mode (Shaver is switched off but connected to the mains) Some minutes after completing the charging, the shaver switches to the stand-by-mode: The display turns off. Low charge indicator: The red « » charge indicator blinks to indicate that the charge has dropped below 20%, provided the shaver is switched on. The remaining battery capacity is suffi cient for 2 to 3 shaves. 27 Charging information • A full charge will take about 1 hour and provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth. 5-minute quick charge is suffi cient for a shave. • Recommended temperature for recharging is 5°C to 35°C. Outside the recomme...