Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
3). WARNING: Read and understand operator’s manual for unit to be used with this attachment prior to operation. WARNING: To avoid serious personal injury and damage to the unit, shut unit off before removing or installing attachments. Primary Hole Upper Shaft Housing Craftsman Convertible™ Coupler Fig. 2 Lower Shaft Housing Release Button Knob 4. Turn the knob clockwise to tighten (Fig. 1). CAUTION: Lock the release button in the primary hole (Fig. 2) and securely tighten the knob before operating this unit. CAUTION: The attachments with the coupler system are to be used in the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. Fig. 1 Knob Adjustment Bolt Drive Shaft Assembly Angle Adjustment Handle Blade Indexing Ring Tighten Loosen ASSEMBLY INSTRUCTIONS Release Button Guide Recess Knob Fig. 3 WARNING: DO NOT USE an extension boom with this product. It is not designed to be used with an extension and using one may cause serious injury. Hanger Craftsman Convertible™ Coupler Gear Housing ASSEMBLY INSTRUCTIONS Removing the attachment: 1. Turn the knob counterclockwise to loosen (Fig. 1). 2. Press and hold the release button (Fig. 2). 3. While firmly holding the upper shaft housing, pull the hedge trimmer attachment out of the coupler (Fig. 2). OPERATING INSTRUCTIONS BEFORE OPERATING Adjust the angle of the trimmer to suit the area you are trimming; adjust the blade angle based on the situation. Adjust the blade as follows: 1. Grasp the adjustment bolt (Fig. 4) and turn counterclockwise to unscrew the bolt from the hole in the indexing ring. OPERATING TIPS • To trim new growth, use a wide sweeping motion, feeding the blade teeth through the hedge or twigs. The most effective cutting is achieved with a slight downward tilt of the blade. .•Wear gloves when trimming thorny or prickly growth. When trimming new growth, use a wide sweeping action, so that the stems are fed directly into the cutting blade. Older growth will have thicker stems and will be trimmed easiest by using a sawing movement. • Do not try to cut stems that are larger than 7/16 inches (11 mm) thick. Use a non-powered hand saw or pruning saw to trim large stems. • If desired, you can use a string to help cut your hedge level. Decide how high you want the hedge. Then, stretch a piece of string along the hedge at this height. Trim the hedge just above this guide line of string. Trim the side of a hedge so that it will be slightly narrower at the top. More of the hedge will be exposed when shaped this way, and be more uniform (Fig. 5). • To trim the sides of hedges, hold the hedge trimmer at the bottom and sweep upwards. Fig. 4 Fig. 5 2. Rotate the blade to the desired position using the angle adjustment holder. 3. Align the adjustment bolt with the appropriate indexing hole. 4. Screw the bolt into the indexing hole clockwise until hand-tight to secure the blade. DO NOT OVERTIGHTEN. Angle Adjustment Holder WARNING: Dress properly to reduce the risk of injury when operating this unit. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy long pants, boots and gloves. Use a full face shield when needed. Secure hair above shoulder level. WARNING: Keep hands and fingers away from moving parts. Any part of body coming in contact with moving parts could result in serious injury. WARNING: If any parts are missing, damaged, or broken, do not operate your hedge trimmer until they have been replaced. Failure to do so could result in possible serious personal injury. WARNING: Make sure the unit is powered off before adjusting the trimming angle. WARNING: If operating the unit on a slope, stand below the cutting attachment. DO NOT operate on a slope or hilly incline if there is the slightest chance of slipping or losing your footing. Indexing Holes Indexing Ring Check Coupler Engagement Prior to Use 1. Start the unit. 2. Briefly engage and release the trigger. 3. Check that attachment is operating. 4. If the attachment is not operating, remove attachment and repeat steps for installing the attachment. 5. Recheck operation of attachment. Adjustment Bolt WARNING: Before each use, and periodically during use, check to make sure that the adjustment bolt is properly tightened. 6 DANGER: If the blade jams on any electrical cord or line, DO NOT TOUCH THE BLADE. It can become ELECTRICALLY LIVE and VERY DANGEROUS. Release the unit in the safest manner possible, and turn off the power source. MAINTENANCE AND REPAIR INSTRUCTIONS LUBRICATING BLADE WARNING: Before maintenance, be sure your hedge trimmer is disconnected from the power supply. Failure to do so can result in accidental starting, causing serious personal injury. 1. For easier operation and longer blade life, lubricate the hedge trimmer attachment blade before and after each use. Before lubricating, be sure the powerhead is turned OFF. Apply light machine oil along the edge of the top blade strap (Fig. 6). Fig. 6 2. Occasionally, you shoul...