Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
. • Keep cord away from heat, o11,sharp edges, and moving blades. • Wear nonskid footwear. 8 _i, WARNING: When servicinguse only identical Craftsman replacementparts. Useofany other parts may create a hazard or cause product damage. SHARPENING THE CUTTER BLADE See Figure 10. • Allowyourhedge trimmertocometo a stopwith the cutterbladeandguardpositionedasshownin Figure 10. This will allow clearance for the file between cutterteeth and guard teeth. CUTLERBLADE GUARD Fig. 10 • Disconnect Hedge Trimmer from power supply. • Clamp the blade assembly in a vise and file the exposed cutting sudace of each blade tooth with an 8 inch smooth round file, 1/4 in. or 7/32 in, diameter. Be sure to retain the original angle of tooth when filing. • Remove the hedge trimmer from the vise, restart it, and stop it so that the unsharpened edges of the blade teeth are exposed. • Disconnect the tool and repeat the sharpening procedure as described above, LUBRICATION Allofthebearingsinthistoolare lubricatedwitha sufficientamountof highgradelubricantfor the life of the unitundernormaloperatingconditions.Therefore, no further lubricationis required. BLADE LUBRICATION See Figure 11. Disconnect hedge trimmer from power supply. Foreasier operationandlongerbladelife,lubricate the hedge trimmer blade before and after each use. Before lubricating,be sure the switch is in the OFF positionandthe toolisdisconnectedfromthe power supply.ApplylightmachineOilalongthe edgeofthe topstrap as shown in Figure 11. Your trimmer should be stopped, disconnected,and oiledoccasionallyduringuse, OILCAN TOP BLADE STRAP Fig. 11 GENERAL Avoidusingsolventswhen cleaningplasticparts. Most plasticsare susceptibleto damage from various typesofcommercialsolventsandm_y be damaged by theiruse.Use clean clothsto removedirt,carbon dust, etc. _ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic. Onlythepartsshownonpartslist,page 13,are intendedto berepairedor replacedby thecustomer. All other parts representan importantpart of the double insulationsystem and shouldbe serviced only bya qualifiedSears servicetechnician. BLADE REPLACEMENT Disconnect hedge trimmer from power supply. • Remove blade cover screw. See Figure 12, PUSHFORWARD ANDLIFTTO REMOVE BLADECOVER BLADE COVERSCREW Fig. 12 • Remove blade cover: To remove, push blade cover forward and lift from hedge trimmer. • Remove blade screws. See Figure 13. Note: A 5/16 in. socket or nut driver is required to remove blade screws. BLADE COVER BLADE ? SCREWS BLADE ASSEMBLY O BLADE COVER SCREW • Remove grease cover and blade assembly. • Make sure drive washer remains installed on d pin. • Align slot in new blade assembly and grease c with drive washer on gear assembly. See Figu 14. BLADE ASSEMBLYSt.( BLADE ASSEMBLY O ASSEMBLY GEAR WASHER • Afteraligning, continueto hold blade assembly place, then manually slide blade assembly back and forth until screw holes in grease cover align with screw holes in gear housing. See Figure 1A. CAREFULLYSLIDEBLADEASSEMBLYTOALIGN SCREWHOLES--BLADESARESHARP BLADE ASSEMBLY GEAR HOUSING GREASE COVER SCRE' HOLE Fig. 13 Fig. 10 BLADE REPLACEMENT (Continued) WARNING: Blades are sharp. When manuallyslidingblade assembly, do not place your hand or fingersbetween blades or in any position where they couldget pinchedor cut, • Replace blade screws. Tighten screws securely. • Replace blade cover screw. See Figure 16. Note: Donettightenuntilbladecoverhasbeen replaced. BLADECOVER REARTAB BLADE BLADE SCREWS Fig. 16 • Replace bladecover. Placereartab insidehousing, align front tabswithslotsinhousing,then slide blade cover back intoits correct position.Sea Figure 17. BLADECOVER FRONTTABS SUDEBLADECOVER BACKINTOPosmoN Fig. 17 • Tighten bladecoverscrewsecurely. _1= WARNING: Makesurebladecoverisreplaced before connectingyour hedge trimmerto power supply. Failureto do so will expose internalparts whichcould cause an accident or electrical shock resuttinginseriousinjury, Note: If binding occursafter replacingblade assembly, repeat the stepsabove for reassembly. 11 CRAFTSMAN 20 in. HEDGE TRIMMER -MODEL NUMBER 315.798890 SEE NOTE "A" PAGE 13 2 4 14 13 9 II 10 11 i 12 CRAFTSMAN 20 in. HEDGE TRIMMER -MODEL NUMBER 315.798890 number in all correspondence regarding your HEDGE TRIMMER or when ordering repair parts. I The model number will be found on a plate attached to the motor housing. Always mention the model | I SEE BACK Key Pa_ No. Number 1 703477-057 2 980448-002 3 980458-001 4 999306-025 5 980456-001 6 617900-002 7 990762-001 8 967818-002 9 662961-012 10 990427-001 11 967876-008 12 930517-073 13 990460-001 14 967506-001 972000-600 PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Description Quan. Lock Nut (#1/4-20) ................................................................... 1 Front Handle .....................................................................