Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
For example, the line will wear faster when trimming against a foundation wall as opposed to trimming around a tree. DECORATIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around trees, posts, fences and more. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. 14). USING THE TWIST AND EDGE™ FEATURE Fig. 14 WARNING: Before you begin using any attachment, read and understand the manual that came with the attachment. Follow all safety information contained within. WARNING: To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing add-ons. You can convert this unit to edge grass. 1. Make sure the unit is turned completely off. 2. Turn the knob counterclockwise to loosen coupler (Fig. 15). 3. Push in the release button (Fig. 16) and twist the shaft 90° until the release button snaps into the 90° hole (Fig. 15). 4. Turn the knob clockwise to lock the coupler (Fig. 17). Knob Coupler Fig. 15 90° Edging Hole (Trimmer Only) 8 OPERATING INSTRUCTIONS Craftsman Convertible™ Primary Hole Release Button Coupler Knob Guide Recess Fig. 16 Upper ShaftBoom CRAFTSMAN CONVERTIBLE™ Attachment FEATURE The coupler allows you to convert this unit for use with the following add-on attachments: • Cultivator • Blade Edger • Blower Knob • Brush Cutter Fig. 17 • Pruner CAUTION: These add-on attachments are to be snapped into the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. To Install Attachments NOTE: To make installation easier, place the unit on the ground or on a workbench. 1. Make sure the unit is turned completely off. 2. Turn the knob counterclockwise to loosen the coupler (Fig. 15). 3. While firmly holding the attachment, push it straight into the coupler until the release button (Fig. 16) snaps into the primary hole (Fig. 16). The primary hole is on the opposite side of the coupler from the knob (Fig. 16). Align the release button with the Guide Recess (Fig. 16) to help installation. 4. Turn the knob clockwise to tighten. CAUTION: Before operating this unit, be sure that the release button is fully snapped into the primary hole (Fig. 16), and that the knob (Fig. 17) is securely tightened. To Remove Attachments 1. Make sure the unit is turned completely off 2. Turn the knob counterclockwise to loosen the coupler. 3. Press and hold the release button (Fig. 16). 4. While firmly holding the upper shaft boom (Fig. 17), pull the attachment out of the coupler. 9 MAINTENANCE AND REPAIR INSTRUCTIONS WARNING: To prevent serious injury, never perform maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that the unit cannot start. MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to a Sears or other qualified service dealer. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by a Sears or other qualified service dealer. In order to assure peak performance of your engine, inspection of the engine exhaust port may be necessary after 50 hours of operation. If you notice lost RPM, poor performance or general lack of acceleration, this service may be required. If you feel your engine is in need of this inspection, refer service to a Sears or other qualified service dealer for repair. DO NOT attempt to perform this process yourself as engine damage may result from contaminants involved in the cleaning process for the port. FREQUENCY MAINTENANCE REQUIRED SEE Before starting engine Fill fuel tank with fresh fuel Check oil p. 6 p. 10 Every 10 hours Clean and re-oil air filter p. 11 1st change at 10 hours 2nd change at 25 hours Every 25 hours after Change oil Change oil Clean spark arrestor p. 10 p. 10 p. 13 10 hours on new engine Every 25 hours Every 25 hours Check rocker arm to valve clearance and adjust Check rocker arm to valve clearance and adjust Check spark plug condition and gap p. 12 p. 12 p. 13 CHECKING THE OIL LEVEL The importance of checking and maintaining the proper oil level in the crankcase cannot be overemphasized. Check oil before each use: 1. Stop the engine and allow oil to drain into the crankcase. 2. Place the engine on an elevated, level surface with the cutting head shield hanging off the surface to get a proper oil level reading (Fig. 18). 3. Keep dirt, grass clippings and other debris out of the engine. Clean the area around the dipstick before removing it. Fig. 18 4. Remove the oil fill plug. 5. Look into the oil fill hole, use a flashlight if needed. The oil should be just touching the inner most thread (Fig. 19). 6. If the oil level is not touching the inner most thread on the oil fill hole, add a small...