Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
8 Start/On (I) Stop/Off (O) Throttle Control Fig. 9 7 OPERATING INSTRUCTIONS WARNING: Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit. Craftsman® Primary Hole Release Button HOLDING THE TRIMMER Before operating the unit, stand in the operating position (Fig. 10). Check for the following: • The operator is wearing eye protection and proper clothing • With a slightly-bent right arm, the operator’s right hand is holding the shaft grip Fig. 13 • The operator’s left arm is straight, the left hand holding the assist handle • The unit is at waist level • The cutting attachment is parallel to the ground and easily contacts the grass without the need to bend over TIPS FOR BEST TRIMMING RESULTS • For best trimming results, operate unit with throttle control fully squeezed. • Keep the cutting attachment parallel to the ground. • Do not force the cutting attachment. Allow the tip of the line to do the cutting, especially along walls. Cutting with more than the tip will reduce cutting efficiency and may overload the engine. • Cut grass over 8 inches (200 mm) by working from top to bottom in small increments to avoid premature line wear or engine drag. CRAFTSMAN® CONVERTIBLE™ FEATURE • Cutting from right to left improves the unit's cutting efficiency. Fig. 10 Convertible™ Coupler Knob Guide Recess Knob Attachment Upper ShaftBoom Fig. 14 The coupler allows you to convert this unit for use with the following attachments: • Cultivator • Blade Edger •Blower • Brush Cutter • Pruner To Install Attachments NOTE: To make installation easier, place the unit on the ground or on a workbench. 1. Make sure the unit is turned completely off. 2. Turn the knob counterclockwise to loosen the coupler (Fig. 15). 3. While firmly holding the attachment, push it straight into the coupler until the release button (Fig. 16) snaps into the primary hole (Fig. 16). The primary hole is on the opposite side of the coupler from the knob (Fig. 16). Align the release button with the Guide Recess (Fig. 16) to help installation. 4. Turn the knob clockwise to tighten. To Remove Attachments 1. Make sure the unit is turned completely off. 2. Turn the knob counterclockwise to loosen the coupler. 3. Press and hold the release button (Fig. 16). 4. While firmly holding the upper shaft boom (Fig. 17), pull the attachment out of the coupler. USING THE CRAFTSMAN® CONVERTIBLE™ FEATURE You can convert this unit to edge grass. 1. Make sure the unit is turned completely off. 2. Turn the knob counterclockwise to loosen coupler (Fig. 12). 3. Push in the release button (Fig. 13) and twist the shaft 90° until the release button snaps into the 90° hole (Fig. 12). 4. Turn the knob clockwise to lock the coupler (Fig. 14). WARNING: Before you begin using any attachment, read and understand the manual that came with the attachment. Follow all safety information contained within. WARNING: To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing attachments. Knob Coupler CAUTION: These attachments are to be snapped into the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. CAUTION: Before operating this unit, be sure that the release button is fully snapped into the primary hole (Fig. 13), and that the knob (Fig. 14) is securely tightened. Clippings are thrown away from the operator. • Slowly move the trimmer into and out of the cutting area at the desired height. Move either in a forward-backward or side-to-side motion. Cutting shorter lengths produces the best results. • Trim only when grass and weeds are dry. • The life of your cutting line is dependent upon: – proper adherence of explained trimming techniques, what – vegetation is cut, and – where vegetation is cut. For example, the line will wear faster when trimming against a foundation wall as opposed to trimming around a tree. DECORATIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around trees, posts, fences and more. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. 11). 90° Edging Hole(Trimmer Only) Fig. 11 Fig. 12 8 MAINTENANCE AND REPAIR INSTRUCTIONS LINE REPLACEMENT for Hassle-Free™ Cutting Head WARNING: Do not remove or alter the line cutting blade assembly. Excessive line length will make the clutch overheat. This may lead to serious personal injury or damage to the unit. Always use Craftsman® Hassle-Free™ XTRA QUIET Spiral Line. Choose the line size best suited for the job at hand. Red colored line is designed for cutting grass and small weeds. Black colored line is designed for cutting larger weeds and light brush. NOTE: Before inserting new line into the holes in the cutting head, identify the proper holes. Follow directions as shown on the line glide plate. Do Not attempt to remove the cutting head from the unit when replacing line. 1. Remove the old line and line glide CuttingLine Glide plate fro...