Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
CAUTION: Confirm that the tube is locked in place by releasing the button and pushing down on the tube. ATTACHING EXTENSION CORD • An extension cord retainer (figure 7) is built into the switch handle that prevents the cord from coming unplugged. To use this feature, simply double the extension cord about 8 inches (203mm) from the end, and insert it into the slot in the bottom of the handle area. Hook the loop formed by doubling the cord over the tab. Gently tug on the cord to insure that it is firmly retained in the trimmer’s handle. Plug the receptacle end of the extension cord into the plug blades in the trimmer. OPERATING INSTRUCTIONS WARNING: Always use proper eye protection that conforms to ANSI Z87.1 (CAN/CSA Z94.3) while operating this power tool. CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence. SWITCHING ON AND OFF • To switch the tool on, squeeze the trigger lever. • To switch the tool off, release the trigger lever. • With the unit on, angle unit and slowly swing the trimmer side to side as shown in figure 8. • To operate as a maintenance edger, unplug the unit from the power source. Push the button and rotate the tube 180° as shown in figure 6. The tool will lock in position. Gently pull the wire edge guide down into place as shown in figure 9 and position the trimmer above the surface as shown in figure 9. • Return to the trimming position by unplugging the unit from the power source, pushing the button and rotating the tube back 180°. The tool will lock in the trimmer position. When using the tool return the wire edge guide to the original position, out of the way. BLOWER FUNCTION (GH750 ONLY- FIGURE 10) The GH750 funnels the air created by the motor up through the guard creating a built-in sweeper. This feature can be used to blow grass clippings off of sidewalks and other hard surface areas. CUTTING LINE / LINE FEEDING Your trimmer uses .065 inch (1.65 mm) diameter, ROUND nylon line. During use, the tips of the nylon lines will become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of line. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. The advanced automatic line feeding mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever it’s required. DO NOT BUMP unit on ground in attempt to feed line or for any other purposes. FITTING A NEW SPOOL OF AFS CUTTING LINE (FIGURES 11 & 12) • Unplug the tool. • Depress the tabs (a) and remove the cassette (b) from the cassette housing (c) in the trimmer head (figure 11). • Grasp empty spool (d) with one hand and cassette with other hand and pull spool out from cassette. If lever (e) in base of cassette becomes dislodged, replace in correct position before inserting new spool into cassette. • Remove any dirt and grass from the cassette and housing. • Take the new spool and push it onto the boss (f) (figure 12) in the cassette. Rotate the spool slightly until it is seated. • Unfasten the end of one of the cutting lines and guide the line into one of the eyelets (g). figure 12. The line should protrude approximately 4-3/8 inches (111mm) from the cassette. • Unfasten the end of the other cutting line and guide the line into the other eyelet. The line should protrude approximately 4-3/8 inches (111mm) from the cassette. • Align the cassette tabs (a) with the slots (h) in the housing (figure 11). • Push the cassette onto the housing until it snaps securely into place. CAUTION: To avoid tool damage, If the cutting lines protrude beyond the trimming blade (i), cut them off so that they just reach the blade (figure 11). WINDING NEW LINE ONTO AN EMPTY SPOOL (FIGURES 13 &14) You may wind new cutting line onto an empty spool. Replacement packs of .065 inch (1.65 mm) cutting line are available from your local dealer. • Remove the empty spool from the tool as described in “FITTING A NEW SPOOL OF AFS CUTTING LINE”. • Remove any remaining cutting line from the spool. • First wind new line onto the uppermost part of the spool. - Feed 3/4 inch (19mm) of cutting line into one of the line anchoring slots. - Wind the cutting line onto the spool in the direction of the arrow on the spool. Make sure to wind the line on neatly and in layers. Do not crisscross (figure 13). - When the wound cutting line reaches the recesses (j), cut the line. (figure 14). - Temporarily park the line in the holding slots (k) on one side of the spool as shown in the inset in figure 14. • Repeat the above procedure for the second cutting line on the lower section of the spool. • Fit the spool onto the tool as described in “FITTING A NEW SPOOL OF ...
Эта инструкция также подходит к моделям:Машинки для стрижки - GH750 (2.46 mb)