Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
. Check if the voltage indicated on the powerplug corresponds to the local mains voltage before you connect the appliance. . Only use the powerplug supplied. . The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this will cause a hazardous situation. . Do not use the appliance when the cutting unit is damaged or broken, as this may cause injury. . Do not use a damaged powerplug. . If the powerplug is damaged, always have it replaced by one of the original type in order to avoid a hazard. . Make sure the appliance and the powerplug do not get wet. . Keep the appliance out of the reach of children. . Use, charge and store the appliance at a temperature between 15C and 35C. cc . This appliance is only intended for trimming the human beard. Do not use it for any other purpose. Charging Charge the appliance fully before you star t using it for the first time or after a long period of disuse. 1 2 Make sure the appliance is switched off before you start charging it. Insert the appliance plug into the appliance and put the powerplug in the wall socket. . The charging light goes on to indicate that the appliance is charging (fig. 2). . It will take approx. 10 hours to fully charge the battery. . A fully charged appliance has a cordless trimming time of up to 50 minutes. B When the appliance has been charged for the first time, we advise you to use it until the batter y is completely empty. B For a single trimming session the appliance must be charged for at least 90 minutes. Optimising the lifetime of the rechargeable battery. -After the appliance has been charged for the first time, use it until the batter y is completely empty. -Do not charge the appliance for more than 24 hours. -Do not keep the powerplug plugged into the wall socket all the time. -Do not recharge the appliance between trimming sessions. -Discharge the batter y completely twice a year by letting the motor run until it stops.Then fully recharge the batter y. -If the appliance has not been used for a long period of time, it must be fully recharged. Preparing for use Always comb your beard or moustache with a fine comb before you star t trimming. Using the appliance Corded trimming (QT4060 only) Do not run the appliance from the mains when the battery is fully charged. B If the batter y is low, you can also use the appliance from the mains: 1 Switch the trimmer off, connect it to the mains and wait a few seconds before switching it on. 2 If the battery is completely empty, wait a few minutes before switching the appliance on. Absorbing cut hairs The suction system is activated automatically as soon as you switch the appliance on. It absorbs cut hairs during every kind of use, i.e. trimming with and without comb attachment and contouring.The flexible hair guide follows the contours of the face and directs cut hairs towards the nozzle of the vacuum mechanism. 4203 000 313827 We advise you to empty the hair-collection chamber after each trimming session. When trimming long, dense beards it may also be necessary to empty the hair-collection chamber during the trimming session in order to maintain optimal suction performance (also see chapter 'Cleaning', section 'Haircollection chamber'). B To ensure optimal functioning of the vacuum system, do not cut off more than approx. 7mm of your overall beard length at a time. If you want to cut your beard shorter, repeat the process one or more times. Trimming with comb attachment 1 Turn the adjustment ring (Precision Zoom Lock`) to the desired trimming length setting (see table) (fi g. 3). . The setting will appear in the window below the adjustment ring (Precision Zoom Lock`). If you are trimming for the first time, start with the maximum trimming length setting (9). 2 To trim in the most effective way, move the trimmer against the direction of hair growth. Do not move the trimmer too fast. Make smooth and gentle movements and make sure the surface of the comb always stays in contact with the skin (fi g. 4). Trimming at the unique 'stubble look' setting . Use the trimmer with the comb attachment set to length setting 1.This allows you to create a 'stubble look' (fig. 5). Trimming without comb attachment Full beards and single hairs. 1 Remove the comb attachment (fi g. 6). B Never pull at the flexible top of the comb attachment. Always pull at the bottom part. 2 Make well-controlled movements and touch the hair lightly with the trimmer (fi g. 7). Cleaning The appliance may only be cleaned dry. Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. Never use sharp or hard objects to clean the filter to avoid damaging it. Hair-collection chamber 1 2 3 4 Switch the appliance off. Remove the hair-collection chamber and remove the hairs by shaking or brushing them out (fi g. 8). For extra thorough cleaning and to maintain optimal suction performance, detach the fi lter... (fi g. 9). ...and carefully clean the hair-collect...
Эта инструкция также подходит к моделям:Машинки для стрижки - QT4060/00 (1.01 mb)