Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
4 Press the setting selector (1) and slide the comb to the desired hair length setting (2). Then release the setting selector to lock the hair length setting (Fig. 5). hair length settings -The settings are shown on the arms of the comb. The settings correspond to the remaining hair length after cutting (Fig. 6). -The small comb cuts the hair to a length of 3mm, 6mm, 9mm, 12mm, 15mm, 18mm or 21mm. -The large comb cuts the hair to a length of 24mm, 27mm, 30mm, 33mm, 36mm, 39mm or 42mm. 5 6 Switch on the appliance (Fig. 7). Move the appliance through the hair slowly. Note: Make sure that the flat part of the comb is fully in contact with the scalp to obtain an even cutting result. Tips: -Star t clipping at the highest hair length setting of the comb and reduce the hair length setting gradually. -Write down the hair length settings you use to create a cer tain hairstyle as a reminder for future clipping sessions. -To clip most effectively, move the appliance against the hair growth direction. -Tr y different directions (upward, downward or across), because hair doesn’t all grow in the same direction. -Make overlapping passes over the head to ensure that the appliance catches all the hairs that need to be cut. -Make sure that the flat par t of the comb is fully in contact with the scalp to obtain an even cutting result. -To achieve a good result with curly, sparse or long hair, you can use the styling comb to guide the hair towards the appliance. -Regularly remove cut hair from the comb. If a lot of hair has accumulated in the comb, remove it from the appliance and blow and/or shake the hair out of it. Clipping without comb You can use the clipper without comb to contour the neckline and the area around the ears. The comb keeps the cutting unit at a cer tain distance from the head.This means that, if you use the clipper without the comb, the hair is cut off ver y close to the skin. 1 Press and hold the setting selector (1) with one hand and pull the comb off the appliance (2) with your other hand (Fig. 8). Never pull at the flexible top of the comb. Always pull at the bottom part. 2 3 4 5 6 Before you start to contour the hairline round the ears, comb the hair ends over the ears. Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends. Only cut the hair ends. The hairline has to be close to the ear. To contour the neckline and sideburns, turn the appliance and make downward strokes. Move the appliance slowly and smoothly. Follow the natural hairline. graduation The Philips hair clipper not only allows you to cut the hair evenly at the same length all over the head, it also enables you to achieve a smooth transition from longer hair on top of the head to shor ter hair on the back and sides of the head. 1 2 3 4 Slide the large comb into the guiding grooves of the appliance (‘click’) (Fig. 4). Start clipping at the setting for maximum hair length (42mm). Then choose a shorter setting and cut the hair on all parts of the head, except for the top, where you want the hair to be longer. Repeat this procedure until all hairs have the desired length. Cutting over styling comb or fingers This technique can be used to obtain hair lengths over 42mm. Bear in mind that this technique is difficult to master and should only be applied by experienced users. 1 Press and hold the setting selector (1) with one hand and pull the comb off the appliance (2) with your other hand (Fig. 8). Never pull at the flexible top of the comb. Always pull at the bottom part. 2 3 4 5 Comb a small section of hair upwards. Lift the hair with the styling comb and hold it between your fingers until only the length that needs to be cut sticks out. Cut the hair protruding from the comb or fingers. Continue this procedure and comb frequently to remove cut hair and to check for unevenly cut sections. Cleaning Clean the appliance ever y time you have used it. Never use scouring pads, abrasive cleaning agents or aggressive liquids such as alcohol, petrol or acetone to clean the appliance. Only clean the appliance with the cleaning brush supplied. Note:The appliance does not need to be lubricated. 1 Make sure the appliance is switched off and disconnected from the mains. 2 Press and hold the setting selector (1) with one hand and pull the comb off the appliance (2) with your other hand (Fig. 8). Never pull at the flexible top of the comb. Always pull at the bottom part. 3 4 5 6 Push the middle part of the cutting unit upwards with your thumb until it opens (Fig. 9). Clean the cutting unit with the cleaning brush supplied (Fig. 10). Clean the inside of the appliance with the cleaning brush supplied (Fig. 11). Close the cutting unit (‘click’). Replacement Only replace a damaged or worn cutting unit with an original Philips cutting unit. 1 2 Push the middle part of the cutting unit upwards with your thumb until it opens and then pull it off the appliance (Fig. 9). Place the lug of the new cutting unit into the slot and p...
Эта инструкция также подходит к моделям:Машинки для стрижки - CC5065/17 (755.2 kb)