Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
-Do not keep the appliance plugged in continuously. Corded clipping When the rechargeable battery is empty, you can also run the appliance from the mains. To use the hair clipper connected to the mains: 1 2 Switch off the hair clipper and connect it to the mains. Wait a few seconds and then switch on the appliance. Using the appliance Display indications The display is activated when you press the on/of button and when you turn the length adjustment ring. -During clipping, the display provides the following information: (Fig. 4) The selected hair length (i.e. the remaining hair , length after clipping) in millimetres. ’--’ when no comb is attached to the appliance , ‘THIN’ when the thinning comb is attached to the , appliance The remaining battery charge. , ’E’ if the cutting unit is blocked. , Clipping with the small and large clipping comb Make sure you use the right comb. If you use the thinning comb instead of the small or large clipping comb, only part of the hairs will be cut. Select the small or large clipping comb, depending on the desired hair length. -The hair length settings are indicated in millimetres on the display of the appliance.The settings correspond to the remaining hair length after cutting (Fig. 5). -The small clipping comb cuts hair to a length between 3mm and 22mm in steps of 1mm. -The large clipping comb cuts the hair to a length between 23mm, and 42mm in steps of 1mm. 1 2 Slide the comb into the slot in the appliance (‘click’) (Fig. 6). To set the comb to the desired hair length setting, turn the hair length adjustment ring to the left or to the right (Fig. 7). The display shows the selected hair length. ,3 Switch on the appliance. Tips -We advise you to star t clipping at the highest setting of the large clipping comb and to reduce the hair length in small steps until you reach the desired hair length. -If a lot of hair has accumulated in the comb, remove the comb and blow and/or shake the hair out of it. Removing the comb does not change the set hair length setting. -Write down the hair length settings you have used to create a cer tain hairstyle as a reminder for future clipping sessions. Clipping with the thinning comb Make sure you use the right comb. If you use the small or large clipping comb instead of the thinning comb, all the hair will be clipped at the same length. -The thinning comb cuts hair to a length between 3mm and 22mm in steps of 1mm. -With the thinning comb, you can give your haircut a natural look and it allows you to create a smooth transition between two different hair lengths. - The thinning comb cuts only half of the hair that enters the comb, which results in a natural look (Fig. 8). Thinning an entire haircut We advise you not to use the thinning comb for very short haircuts. Slide the thinning comb into the slot in the appliance (‘click’) (Fig. 6). 1 2 Set the thinning comb to a lower setting than the one you just used for the small or large clipping comb to create the haircut. How much lower the setting for the thinning comb should be depends on your hairstyle and hair length. However, never use the thinning comb at a setting that is lower than half the setting you used to create the haircut. For example, if you used the large clipping comb at 30mm to create the haircut, do not use the thinning comb at a setting lower than 15mm. 3 4 Switch on the appliance. Move the thinning comb through the hair. Make sure the thinning comb only touches each spot once, otherwise it cuts all the hair to the set hair length. Creating a smooth transition between two hair lengths If you have cut your hair to two different lengths, you can use the thinning comb to create a smooth transition between these two lengths. 1 2 Slide the thinning comb into the slot in the appliance (‘click’) (Fig. 6). Set the thinning comb to a hair length setting that is halfway between the two hair length settings you used to create the haircut. For instance, if you have cut top par t of the haircut to a length of 20mm and the bottom par t of the haircut to a length of 10mm, set the thinning comb to 15mm. 3 Move the thinning comb upwards through the transition between the two lengths (Fig. 9). Make sure the thinning comb only touches each spot once, otherwise it cuts all the hair to the set hair length. Clipping without comb You can use the clipper without comb to contour the neckline, the area around the ears and sideburns. The comb keeps the cutting unit at a cer tain distance from your head.This means that, if you use the clipper without comb, your hair is cut off very close to the skin. 1 To remove the comb, pull it off the appliance (Fig. 10). Never pull at the flexible top of the comb. Always pull at the bottom par t. 2 3 Switch on the appliance. Hold the appliance with the cutting unit pointing upwards and make downward strokes with the regular trimmer (the broad side of the cutting unit). Be careful, the trimmer removes every hair it touches. Using the precision trimmer The precision tr...
Эта инструкция также подходит к моделям:Машинки для стрижки - QC5770/44 (888.01 kb)