Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Fitting the blade guard and saw blade • The blade guard (A) is fitted using 4 screws (L) as shown. CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Place the blade (D) and support flange (F) on the output shaft. • Fit the nut (G). Tighten the nut to a torque of 35-50 Nm. Use the socket spanner in the tool kit. Grasp the handle of the spanner as close to the blade guard/combination guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread). When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut. Fitting the trimmer guard and trimmer head Trimmy SII • Fit the correct trimmer guard (A) for use with the trimmer head. Secure the trimmer guard using the 4 screws (L) and the support plate (M) as shown. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. • Tighten the trimmer head to a torque of 35-50 Nm. • To dismantle, follow the instructions in the reverse order. ! WARNING! Tighten the lock screw (N) in the center hole of the support cup. Tighten to a torque of 35-50 Nm (3.5-5.0 kpm), CAUTION! Left-hand thread. If the lock screw is not fitted in the support cup, there is a risk that the support cup will come unscrewed. This means that the blade will also come loose, which could result in serious or fatal injury to the operator or others. L A G F D B C B A L M C H English – 19 ASSEMBLY Fitting other guards and cutting attachments Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Secure the trimmer guard using the 4 screws (L) and the support plate (M) as shown. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. • To dismantle, follow the instructions in the reverse order. Adjusting the harness and clearing saw Standard harness Safety release At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness. Spreading the load on your shoulders A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders. Correct height 1 Forestry clearing The machine should be supported in a harness when forestry clearing so that the cutting equipment is angled slightly forwards in relation to the ground. Adjust the height using the strap on the harness for the support hook. 2 Grass clearing The machine should be supported in a harness when grass clearing so that the cutting equipment is parallel to the ground. Triobalance harness Safety release Push down the red release lever to release the machine from the harness. ! WARNING! When using a clearing saw it must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release. B A L M C H H 20 – English ASSEMBLY Adjusting the harness 1 Tighten the hip strap so that it sits securely. 2 Tighten the chest strap under your left arm so that it fits closely around your body. 3 Adjust the shoulder strap to distribute the load evenly across your shoulders. Press downwards on the suspension hook to load the harness. 4 Adjust the height of the suspension hook as described in the instructions for the standard harness. (Forestry clearing) 5 If you need to lower the suspension hook, for trimming for example, move the suspension strap (A) to the lower mounting point on the backplate. 6 The elastic strap (B) can be tightened to transfer more load from the shoulder straps to the hip strap. Correct balance 1 Forestry clearing The machine is balanced by moving the support ring on the machine forwards o...
Эта инструкция также подходит к моделям:Машинки для стрижки - 240F (2.88 mb)