Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Do not allow people into the starting area. STARTING COLD ENGINE • Slide ignition switch to START RUN position as shown (FORWARD) Turn choke lever to START (Close) position • Squeeze throttle trigger slightly and pull starter handle several times until first firing sound Now, turn choke lever to RUN (Open) position, and if necessary, restart the engine • When engine has been started, release throttle trigger and allow to warm up for a few minutes before using • After idling, gradually squeez throttle trigger and cutter head will start to operate as the engine attains clutch engagement speed of 3000 RPM approximately START RUN Ignition switch Throttle trigger (NOTE) Recoil starter Use short pulls—only 1 2—2 3 of starter rope for starting Do not allow the starter handle to snap back against the casing. Always hold the unit firmly CAUTION DO NOT RUN THE ENGINE ON FULL THROTTLE WITHOUT CUTTER HEAD TO AVOID ENGINE DAMAGE METRIC GAS OIL _I_ LITERS CC 4 | 125 8 250 20 625 brand motor oil or an aircooled two stroke Gasoline 32 7 STARTING WARM ENGINE • When engine is warm, start it by pulling recoil starter rope with switch positioned at START RUN (Keep choke lever in RUN (Open) position ) • If engine does not start in a few tries, follow same procedures as to start cold engine. STOPPING ENGINE • Release throttle trigger and allow to run at an idle speed • Slide back ignition switch to ' STOP" position (NOTE) When engine does not stop, shift choke lever to close position Check and repair stop switch before starting the engine again GENERAL TRIMMING INSTRUCTIONS Prior to using your trimmer, familiarize with the safety instructions listed in the Operator's Manual, and all local regulations for the operation of your unit These instructions and regulations are for the protection of the operator For all types of operations, always hold the trimmer securely with both hands, with thumbs and fingers encircling handle and grip CAUTION • Do not allow either people or animals into the work area. • Always wear safety goggles, gloves, non-skid foot wear • DRESS PROPERLY-Avoid loose clothing • Before starting operation, inspect stones or any other foreign obiect(Can. bottle, steel wire etc ) in the area and remove them. • When two or more operators are working together, ensure that a safe distance is kept between them • Keep both hands on the grips when power is on. • Engine continues running even when cutter head has stopped due to an excessive load In such cases, stop the engine and remove the cause of overloaded before again starting the engine and resuming the job • When grass or weed have clogged the cutter head affecting normal operation, first.stop the engine and remove them • Do not overreach or stand on unstable support • In the event, that the cutter head strikes an obstruction, or is otherwise prevented from rotating in normal operation, the centrifugal clutch will slip to prevent engine damage In this case, stop the engine free and examine the cutter head and if in good order, resume operation. • Should the trimmer be operated for an extended period in high temperatures, the drive shaft housing may become very hot. If too hot to touch, allow the unit to cool down, check the lubrication as per 'Maintenance and continue to operate irate if in order • To avoid engine damage, do not run on full throttle without load • Do not operate the trimmer without the shield correctly fitted • Always inspect the work area and remove any foreign objects READ CAREFULLY SAFETY INSTRUCTION (Page 1) Ignition switch STOP Throttle trigger 8 For most cutting and trimming jobs, 13 ~ 15 cm (five ^ six inches) of cord {measured from the edge of the cutting head to the tip of the cutting cord) is recommended. Remember that cutting is done with the tip of the cord. Do not attempt to cut with the entire length of the cord. This will result in the cord snapping or fraying, thereby reducing the cutting efficiency and also will result in using more cord than necessary. * Length of cord depends on the models. Refer to page4 and 5. CUTTING PROCESURES Place the trimmer with the cutter head facing straight ahead. Always trim from the right to the left tilting the unit slightly to the right allowing the debris to the thrown away from the operator. (CAUTION) Letting the cutter head tilt to the left will result in debris being thrown back towards the operator. (SEE ILLUSTRATIONS Aand B) SCALPING Scalping is the removal of all vegetation down to the ground. For this operation, tilt the cutter head about 30°. Ensure the head is tilted to the right. (SEE ILLUSTRATION C) Scalping around trees and bushes is particulary effective, but care should be exercised not to bruise the bark of young and sensitive growth. In flower beds, always remember that the nylon cord will cut in a complete circle to avoid cutting flowers instead of weeds. EDGING Tilt the cutter head to a vertical position. Allow ...
Эта инструкция также подходит к моделям:Машинки для стрижки - GT-160 (1.03 mb)
Машинки для стрижки - GT-200A (1.03 mb)