Оценок - 3, средний балл: 4.3 ( )

Производитель: Homelite Размер: 1.08 mb Название файла: Язык инструкции:

TO STOP THE ENGINE: See Figure 13. To stop the engine, push and hold the STOP button until the engine stops. IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT: Do not return this product to the retail store where it was purchased. Please call our Customer Service Department for any issues you may have. For Help Call: 1-800-242-4672 PRIMER BULB CHOKE LEVER STOP BUTTON Fig. 13 FULL CHOKE (A) HALF CHOKE (B) RUN (C) MAINTENANCE WARNING: Use only original manufacturer's replacement parts, accessories and attachments. Failure to do so can cause poor performance, possible injury and may void your warranty. You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorized service dealer. SPOOL REPLACEMENT EZ LINE™ TAP ADVANCE SYSTEM NEW PREWOUND SPOOL See Figures 14 and 15. If replacing string only, refer to “String Replacement” later in this manual. Use only .080 in. (2.0 mm) diameter monofilament string. Use original manufacturer's replacement string for best performance. 1. Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. To remove the spool retainer: Turn the spool retainer counterclockwise for Trimlite and Trim n’ Edge. Turn the spool retainer clockwise for Easy Reach. 2. Remove the empty spool from the string head. Keep the spring attached to the spool. 3. To install the new spool, make sure the two strings are captured in the slots opposite each other on the new spool. Make sure the ends of each string is extended approximately 6 in. (152 mm) beyond each slot. 4. Thread the strings into the eyelets in the string head. Carefully push the spool into the string head (gently pull the strings to the outside if necessary). When the spool is positioned in the string head, grasp the strings and pull sharply to release them from the slots in the spool. 5. Push down and turn the spool counterclockwise until it no longer turns. Hold the spool down and rotate clockwise a small amount. Release the spool. The spool should be locked down in the string head. If not, hold down and rotate until locked. 6. Make sure the string head and the spool retainer are installed on the drive shaft. To install the spool retainer: Turn the spool retainer clockwise for Trimlite and Trim n’ Edge. Turn the spool retainer counterclockwise for Easy Reach. Fig. 14 Fig. 15 SPOOL RETAINER SPRING SLOTS STRING HEAD EYELETS SHAFT 7. Pull the strings again to rotate the spool into cutting position. Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head. Page 16 MAINTENANCE STRING REPLACEMENT See Figures 16, 17, 18 and 19. 1. Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. To remove the spool retainer: Turn the spool retainer counterclockwise for Trimlite and Trim n’ Edge. Turn the spool retainer clockwise for Easy Reach. 2. Remove the spool from the string head. NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool. 3. Cut two pieces of string, each being approximately 9 ft. (2.7 m) long. Use only .080 in. (2.0 mm) diameter monofilament string. 4. Insert the first string into the anchor hole in the upper part of the spool. Wind the first string around the upper part of the spool counterclockwise, as shown by the arrows on the spool. Place string in the slot on upper spool flange, leaving about 6 in. (152 mm) extended beyond the slot. Do not overfill. After winding the string, there should be at least 1/4 in. (6 mm) between the wound string and the outside edge of the spool. 5. Repeat above step with second string, using the bottom part of spool. Do not overfill. 6. Replace the spool and the spool retainer. Refer to “Spool Replacement” earlier in this manual. CLEANI...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: