Оценок - 3, средний балл: 4.7 ( )

Производитель: Electrolux Размер: 2.08 mb Название файла: Язык инструкции:

L5. Fuel filter To clean or replace the filter, remove the cap on the tank and take the filter out using a hook or long-nose pliers. Periodically, every season, contact your service center for general maintenance and cleaning of the inside. This will reduce the possibility of unexpected problems and will ensure the good performance and long life of your machine. . CAUTION! Regularly it is important, in order to prevent the engine from overheating, to remove the dust and dirt from the vents, the cylinder cover and fins on the cylinder, using a wooden scraper. . CAUTION! In case of prolonged disuse, empty the fuel tank and run the engine until it is out of gas. Store the brush cutter in a dry place. L6. Attachments maintenance (for split shaft modelsonly) Follow maintenance instructions on the attachment manual. M. Replacement of nylon string . CAUTION! Use only the recommended type of nylon string. Do not use steel wires for any reason, in order to prevent serious injury. M1. String replacement (String head A) (1) If, when you bump the nylon string head on the ground, no more string comes out, it means there is none left and you have to replace it. To replace the reel of string, press both the release pawls indicated by the arrows, remove the empty reel (2), unroll any string left and rewind the new string. (3) Open the original package of string and insert the ends of the two strings in the eyelets on the reel, then wind the strings completely on the reel in the same direction and fasten the end of each string in the 2 opposite grooves. (4) Replace the reel in its housing and thread the ends of the strings in their bushings. Pull each string so that about 15 cm comes out on each side Reassemble the nylon string head as shown. (5) Start the machine and repeat the procedures described in the section “Supply of nylon string”. M2. String replacement (String head B) (1) Loosen the locking nut on the base of the nylon head by turning it clockwise.(2) Remove the base cover assembly. Remove the empty spool from the housing and discard any remaining line. (3) Prepare 2 lengths (8ft each) of 2.4 mm nylon line. Thread 1 end of each line into the two holes on opposite sides of the spool. Pinch the exposed ends flat with a pair of pliers to prevent them slipping through the hole.(4) Wind the two lines in the same direction around the spool. (5) Slide the end of the two lines into the grooves to hold the line temporarily. (6) Position the spool back into the housing and pull the line through the eyelets. (7) Pull about 15cm (6inch) of line out on either side. (8) Reassemble the nylon string head as 8-ENGLISH illustrated; mower gauge,spring and locking nut (tighten Replacement of the complete nylon string head in an anti-clockwise direction). If upon visual inspection (and in any case after a violent bump) the casing on the nylon string head appears Replacement of entire string reel damaged, it should be replaced. For this operation see If the reel becomes excessively worn, replace it with a “Usable cutting tools and their installation on the whole new reel. machine”. N. Cutting techniques . CAUTION! Before using the machine read the following chapters carefully: “Safety Precautions” and “Description of safety devices”. . CAUTION! Always wear the recommended personal protection gear. . CAUTION! Before using the machine, make sure all the parts are properly assembled. . CAUTION! In mounting the cutting utensils follow the instructions in the chapter entitled “Usable cutting tools and their installation on the machine”. ABSOLUTELY DO NOT USE THE BRUSH CUTTER IF THE SPECIFIC SAFETY GUARD FOR THE CUTTING DEVICE IN USE IS NOT SECURELY FASTENED (see chapter “Assembly of safety guards”). Failure to follow this rule can expose you to serious danger such as: a) possible contact with rotating and cutting parts b) possible contact with flying debris. . CAUTION! Do not use worn or damaged cutting devices. . CAUTION! Try to limit contact and impact of the cutting devices against the ground and other objects as much as possible. Hold the cutting device away from your body. . CAUTION! Twigs or grass may jam between the safety guard and the blade or nylon strin...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: