|
Фрагмент инструкции
• Allow the engine to cool before storing or transporting. Be sure to secure the unit while transporting. • Store the unit in a dry area, locked up or up high to prevent unauthorized use or damage, out of the reach of children. • Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after each use, see Cleaning and Storage instructions. (p.19) • Keep these instructions. Refer to them often and use them to instruct other users. If you loan someone this unit, also loan them these instructions. SAVETHESE INSTRUCTIONS SAFETY & INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. WARNING: Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs. WARNINGi READ OPERATOR'S MANuALI Read the operator's manual(s) and fo!low a!! warnings and safety instructions. Failure to do S° can result in Serious injury to the operator andi0r bystandersl © © WEAR EYE AND HEARING PROTECTION WARNING: Thrown objects and loud noise can cause severe eye injury and hearing loss. Wear eye protection meeting ANSI Z87.1 standards and ear protection when operating this unit. Use a full face shield when needed. OIL:Refer to operator's manua! for the proper type of 0i!, THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY WARNING: Do not operate without the cutting attachment shield in place. Keep away from the rotating cutting attachment. I ON/ OFFSTOPCONTROLON / START/RUN O ON / OFFSTOPCONTROLOFFor STOP 15m KEEP BYSTANDERS AWAY WARNING: (50.) Keep all bystanders, especially children and pets, at least 50 feet (15 m) from the operating area. DO not tOUCh a hot muffler, gear housing or cylinder. You may get burnedl These parts get extreme!y h0 t from 0pera _ tion. They remain hot for a Short time after the unit turned off. SHARP BLADE WARNING: Sharp blade on cutting attachment shield. To prevent serious injury, do not touch the line cutting blade. Starter Rope Muffler Guard Grip Fast Idle Lock Spark Plug Safety Trigger On ! Off Control Serial Number Upper Handle Air Filter Attachment Cover Hassle Free TM Cutting Head Shaft Attachment Coupler Anti-Kickback Throttle Control Shaft Grip / Propane Canister Bar NOTE: This illustration may differ from your unit. For example, the picture shows a straight shaft; your unit may have a curved shaft. TOOL KIT Your unit is provided with a tool kit (Fig.l). This tool kit consists of the following: 4 mm Allen Wrench 5 mm Allen Wrench _.// 8 & 10 mm Wrench Four 5 mm Screws _ (/_ with captive washers I _ FourWashers Straight Shaft models /_j_--k_J include 2 Plate Washers _ Fig. 1 INSTALLING CUTTING ATTACHMENT SHIELD Use the following instructions if the cutting attachment shield on your unit is not installed. Use only the instructions that apply to the type of shaft and shield that your unit is equipped with. FOR CURVED SHAFT TRIMMERS Place the cutting attachment shield and spacer against tube as shown in (Fig.2). Use the 2 screws provided to clamp the cap and shield onto the tube. Tighten the screws evenly. Make sure the shield does not touch any rotating parts. CuttingAttachment Shield FOR STRAIGHT SHAFT TRIMMERS Place the cutting attachment shield onto the shaft mount. Install using provided hardware in the sequence as shown (Fig.3). Ji Shaft Mount \ I I I I i Cutting Attachment Shield Plate Washer "'_ _ Washer _ Lock Washer Attachin( Screws Fig. 3 INSTALLING THE UPPER HANDLE AND SAFETY BAR 1. Locate the 4 screws included in the tool kit. 2. Assemble the upper handle, safety bar and 4 attaching screws as shown in (Fig.4). Position the handle parts evenly over the rubber sleeve on shaft. Do not completely tighten. 3. While holding the unit in the operating position (Fig. 14), position the upper handle to the location that provides you the best grip. 4. Tighten the clamp screws evenly, until the upper handle is secure. Attaching Screws "_'_I _ g (_jk.1U pper Handle __u bber_Sleeve SafetyBar _ I _"_._-_ Fig. 4 WARNING: To prevent serious injury, never operate the trimmer without the cutting attachment in place. Fig. 2 RECOMENDED OIL TYPE Using the proper type and weight ofoil in the crankcase isextremely important. Check the oil before each use and change the oil regularly. Failure to use the correct oil, or using dirty oil, can cause premature engine wear and failure. Use a high-quality SAE 10W-30 weight oil of API (American Petroleum Institute) service class SF,SG,SH. ADDING OIL TO THE CRANKCASE INITIAL USE NOTE:This unit isshipped without oil in the crankcase. In order to avoid damage to the unit, put oil in the crankcase before you attempt to start the unit. Your unit is supplied with one 2.5 fluid oz. (75 mL) bottle ofSAE10W-30SF,SGorSHoil (Fig.5). 1. Unscrew the top of the bottle of oil and remove the paper se...
Эта инструкция также подходит к моделям:Машинки для стрижки - 104.79211 (2.08 mb)