Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger. insert cartridge fully into the port so that it rests on the charger port floor. Fig. 1 CAUTION : .Your new battery cartridge is not charged. You will need to charge it before use. 0 If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on after you insert a cartridge from a just operated tool. Let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing blade CAUTION : Always be sure that the battery cartridge is removed before installing or removing blade. 0 Insert the blade into the groove in the blade holder until the blade is held by the two protrusions on the blade holder. Fig. 7 CAUTION : Always be sure that the blade is installed properly before operation. 0 To remove the blade, bend both ends of the blade up until it will slip up and over the protrusions. Then pull the blade out. Fig. 8 CAUTION : Replace the used blade before it is worn down too far, or you will have difficulty in bending the ends up to remove it. If this happens, insert a new blade between the used blade and the blade holder, hold the both blades and pull them out. Switch action .To prevent the trigger from being acci- dentally pulled, a lock-off lever is pro- vided as a safety feature. To start the tool, slide the lock-out lever in the direction of the arrow and pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and re- turns to the "OFF" position when re- leased. Operation .Hold the tool firmly without the blade making any contact. Then turn the tool on and gently move the tool back and forth in the area to be cut, keeping the blade parallel with the ground and at the desired cutting height. When cutting tall grass or heavy weeds, proceed slowly. If you attempt to cut too much at a time, the blade may get tangled with weeds, causing the motor to stop. When this happens, turn the tool off immediately and remove the grass or weeds from the blade. Then resume operation. When cutting grass or weeds adjacent to walls, curbing, etc., move the tool slowly and smoothly along the curb with the tip of the blade contacting the curb very lightly. This may cause the curb to be scratched slightly or may cause premature blade wear. However, the tool itself will not be adversely affected. Lock-off lever Fig. 10 Fig. 11 YBlade Y I/ I . // II / / Ground' / / Fig. 1: CAUTION : Forcing the tool may shorten the operating time per battery charge. If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. NOTE : You can expect up to 35 minutes running time on a single charge. MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection .or maintenance. Cleaning blade and blade holder *After operation, clean off the blade and the blade holder with a soft brush. Failure to clean off the blade holder may cause difficulty in installing the blade. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance of adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORI ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Makita Battery cartridge 7000 0 Blade (20 per pkg.) Part No. 632003-2 Part No. 792374-0 0 Fast charger (Model DC7100) 0 Battery holster Holster holds extra battery. Part No. 823033-3C 0 12 V Fast charger Model DC7012 Sep.-12-'85 EN I 120 mm (4-3/4") CORDLESS GRASS TRIMMER @-- Model UM1200D Note: The switch and other part configurations may differ from country to country. MODEL UM1200D Sep.-12-’85 EN ,,!& DESCRIPTION ,& DESCRIPTION 1 1 Compression Spring 3 11 1 Pipe 18 lShaft1 2 1 Lock off Lever 12 1 Motor Housing R 3 1 Grip R 13 1 Motor 4 1 Swwh 14 1 Motor Housing L 5 1 Switch Lever 15 1 Wing Bolt M4x30 6 1 Grip L 16 1 Blade Holder I 1 Wing Bolt M4x30 17 1 Safety Guard 8 1 Name Plate 18 8 Tapping Screw 3x20 9 1 Set Plate 19 1 Tube 4 Guard Ring1 10 1 Battery Holder MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this...
Эта инструкция также подходит к моделям:Машинки для стрижки - UMLZOODW (649.06 kb)