Оценок - , средний балл:
(
)
)
Производитель: Flymo
Размер: 638.58 kb
Название файла: 7af0cf3e-cb25-4eb4-a718-7c49286afdba.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
3. Then fit spool as described in .To fit spool and line complete., section above. Line cutter Manual line feed button Cap Cap release latchSpool Spoolholder Eyelet M N P Q R Cleat Cut out area of spool Eyelet 5 Automatic Line Feed System How the automatic line feed works (M) 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the nylon line hits the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. . Make sure the motor is up to full speed before trimming. 3. If the noise of the nylon line being cut cannot be heard, more line will need to be fed out. 4. To feed more line, it is first necessary to to allow the motor to stop completely, then re-start, allowing the motor to reach full speed. 5. Repeat step 4. until you hear the line hitting against the cut- ter. (Do not repeat this procedure more than 6 times) 6. If problems are experienced with the automatic line feed refer to Fault Finding Chart. To manually feed the nylon line (N) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed button, whilst gently pulling on one of the lines until the line reaches the line cutter. 3. When the required amount of line is fed out, gently pull on the second line (there is no need to press the manu- al line feed button again). 4. If the line extends past the line cutter, too much line has been fed out. 5. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. To remove spool cap 1. Press and hold in the two cap release latches. (P). 2. Pull cap away from the spoolholder. (P). When refitting the spool cap 1. Keep all areas of the cap and spoolholder clean. Failure to do so may prevent the cap being securely located in the spoolholder. 2. Replace the cap, pressing firmly DOWN towards the spoolholder to ensure cap is fully located. 3. Check that the cap is correctly fitted by trying to remove it without depressing the two latches. To replace nylon line. For your convenience it is recommended you buy spool and line complete. Nylon line only is also available. Both are available from Electrolux Outdoor Products stockists. To fit spool and line complete: 1. Remove old spool. 2. Place new spool into spoolholder with cut out areas of the spool in line with eyelets as shown in figure Q. 3. Release one line from cleat and feed line through eyelet (Q). 4. Repeat for second line. . Ensure spool is fully located by gently rotating it during fitment, whilst keeping the spoolholder steady. 5. Refit the cap. To fit nylon line only: . Remember! Your Flymo Trimmer is designed to use only nylon line with a maximum diameter of 1.5mm. Use only genuine Flymo nylon line. 1. IMPORTANT - Always wind the line onto the upper section of the spool first. Take approximately 5 metres of line. Insert 15mm of line into one of the holes in the upper section of the spool (R)and wind line in the direction of the arrows on the top of the spool. Leave approximately 100mm of line unwound and place into cleat as illustrated in figure R. Repeat on lower section of spool. 2. Care should be taken to ensure that the line is neatly coiled on the spool. Failure to do so will impair the effi- ciency of the automatic line feed. 3. Then fit spool as described in .To fit spool and line complete., section above. Line cutter Manual line feed button Cap Cap release latchSpool Spoolholder Eyelet M N P Q R Cleat Cut out area of spool Eyelet 6 6 Fault Finding Chart (Automatic Line Feed only FAULT CHECO ACTION Maintenance Environmental Information After you have finished using your Flymo Mini-Trim follow the procedure below: 1. Disconnect from the mains electricity supply. 2. Never clean your trimmer with water, cleaning flu- ids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 3. Using a soft brush, clean around the inside of the safety guard, the cutting head and the motor housing air vents. (Fig S, T). 4. Inspect the trimmer carefully, especially the parts of the cutting head. 5. If your trimmer is damaged in any way contact your local Electrolux Outdoor Products approved service centre. . Never use a damaged trimmer. 6. Wind cable carefully to avoid kinking. 7. Store in a cool, dry place and out of reach of chil- dren. Is the automatic line feed work- ing? Manually feed out line. Is the line fed out and visible? Has line been removed from cleat? Remove cap and spool, free line and re-fit spool and cap. The line may be jammed on the spool. Rewind line to remove crossed loops. Check that line is in correct section of spool. Is the manual line feed working? Has too much line been fed out? Rewind line. Contact your local approved Service Centre or Electrolux Outdoor Products Customer Service. Is the line cutter missing from the safety g...