Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
NOTE: Correct blade adjustment can only be achieved on clean, oiled blades. Screwing in the screw too tightly may make it impossible for the blades to move. Conversely, not screwing in the screw tightly enough may make the blades of the trimmer feel dull and cause leaves and branches to become caught in the blades of the trimmer. Maintenance WARNING – DANGER UNPLUG THE UNIT BEFORE LUBRICATING OR ADJUSTING THE BLADES. A. Lubrication 1. A few drops of light No. 10 oil should be placed on the back edge of each adjusting screw head approximately after every 4 hours of normal operation. 2. To obtain trouble free trimming, it is necessary to keep the blades lubricated and clean. The gum that collects and builds up on the blades can be removed with a 50-50 mixture of kerosene and No. 10 oil. As petroleum products can shorten the life of some plastics, it is necessary to remove excess oil-kerosene mixture from the plastic parts. 3. When blades are replaced, or any other time that the bottom cover plate is removed, the grease level should be Service maintenance guide checked for proper amount (approximately 1/2 full in the area of the gears) and a new gasket should be used to insure proper seating of the cover plate. Grease should be added every 25 hours of use. Use EP2 white lithium grease in the gear housing. 4. Lubricate male spline part of the drive shaft with EP2 White Lithium grease. B. Storage 1. Store your trimmer in a dry and dust free space, out of the reach of children. 2. Clean the blades thoroughly and coat them with No. 10 oil to prevent rust. 3. Perform all required maintenance and service found in this manual. 4. Use blades cover. Area Maintenance Before use Every 25 hours Every 50 hours Every 100 hours Note Cutting parts Replace if something is wrong Gear case Grease Use EP2 white Lithium grease Screws, nuts bolts Tighten, replace Not adjusting screws Spline (male) Lubricate Use EP2 white Lithium grease Blades Oiling Light #10 oil IMPORTANT: Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Lubricate Inspect/lubricate 1. Remove the side screw, and loosen up other three as shown on the diagram (left). 2. Pull the shaft from the gear housing. 3. Pull and clean internal shaft. 4. Lubricate. 5. Re-install the drive shaft. 6. Do not allow any dirt and dust on the internal drive shaft 7. Do not allow any dirt and dust entering into the gear case 20-25 hrs 9 2 3 4 5 6 8 7 9 58 62 59 60 61 56 55 25 54 22 49 53 52 51 50 20 19 47 48 14 15 16 17 18 19 20 30 45 25 44 42 43 42 41 27 57 12 13 1 1 21 22 23 24 25 26 40 28 29 30 31 32 33 34 35 38 37 36 38 39 63 Hedge trimmer E System exploded view Hedge trimmer E System parts list KEY # DESCRIPTION PART # QTY KEY # DESCRIPTION PART # QTY LOCKNUT INSERT 331534 1 32 GASKET 331233 1 LOCKING KNOB 331218 1 33 GEAR CASE BOTTOM COVER 331234 1 ADJUSTMENT BRACKET 331217 1 34 PROTECTIVE COVER 331235 1 CLAMPING PAD 331535 1 35 BOLT M5X18 331547 4 PLASTIC LOCKING SPACER 331218 5 36 FELT 331236 1 ROTATE BOLT 331536 1 37 SCREW M6X20 331548 1 RIVET 331537 1 38 WASHER 331549 5 FLAT WASHER 331538 1 39 SCREW M6X18 331550 4 CLAMPING LEVER 331219 1 40 FRAME BAR SCREW 331551 2 NUT M5 33...
Эта инструкция также подходит к моделям:Машинки для стрижки - Hedge Trimmer E System (2.42 mb)
Машинки для стрижки - Hedge Trimmer E System (2.42 mb)
Машинки для стрижки - Hedge Trimmer E System (2.42 mb)
Машинки для стрижки - Hedge Trimmer E System (2.42 mb)