Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 19. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. -2- H0600 12V Cordless Trimmer CHARGING SAFETY 1. READ ALL INSTRUCTIONS and warnings on the battery and charger before charging the battery. 2. CHARGE ONLY USING THE SUPPLIED CHARGER AND BATTERY. Do not use with other batteries, chargers or cordless equipment. 3. DO NOT EXPOSE BATTERY OR CHARGER TO WET OR RAINY CONDITIONS. Moisture greatly increases the risk of a shock hazard. 4. DO NOT TOUCH BATTERY POLES with any conductive materials. Touching any two poles at the same time causes a short condition and can cause sparks, electrical shock or fire. 5. DO NOT STORE BATTERY WITH CONDUCTIVE MATERIALS. Storing the battery in a box of screws or nails can cause shorting across the battery poles. 6. DO NOT THROW BATTERY IN FIRE. Combustion of some of the batteries’ component materials can cause toxic fumes and possible explosion. 7. IF CHARGER LIGHT FAILS TO COME ON check the incoming power supply. If power source is okay, then the fuse inside the charger needs replacement. Charger should be serviced by a qualified electrical technician only. 8. DO NOT ATTEMPT TO MODIFY THE CHARGER PLUG. Modifying the plug will result in a safety hazard and will void the warranty. 9. CHARGER IS DESIGNED TO OPERATE AT 110-120 VOLTS. Never try to plug into any circuit that is not 110-120 volts. Never modify or change the plug that is attached to the charger unit to attempt to plug into 220 volt. This can cause serious electrical damage to the unit, possible fire or explosion. Never leave a battery unattended while charging. While charging will make the battery and charging unit warm, if it becomes hot to the touch, disconnect the charger immediately. There is a possibility of fire hazard. Have the battery and charging unit checked by a qualified electrical service technician. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. Consult your local Yellow Pages directory under the category “Recycling” to locate a battery recycler in your area. H0600 12V Cordless Trimmer -3 INTRODUCTION Commentary We are proud to offer the Grizzly Model H0600 Cordless Trimmer. The Model H0600 is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. The Model H0600 offers a 12V motor and cuts a 31.2" wide swath through most light trimming applications. Switch lock keeps it running without holding the trigger to avoid stress and hand fatigue. We are pleased to provide this manual with the Model H0600. It was written to encourage safety considerations and guide you through general operating procedures and maintenance. It represents our effort to produce the best documentation possible. The specifications, details, and photographs in this manual represent the Model H0600 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 2406 Reach Road Williamsport, PA 17701 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com Web Site: To operate this, or any power tool, safely and efficiently, it is essential to become as familiar with its characteristics as possible. The time you invest before you begin to use your Model H0600 will be time well spent. DO NOT operate this tool until you are competely familiar with the contents of this manual. Make sure you read and understand all of the safety procedures. If you do not understand something, DO NOT operate the tool. Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). -4-H0600 12V Cordless Trimmer BEFORE YOU START The battery in your new cordless power tool will not be fully charged when you receive it. Follow the instructions below to charge your battery. Battery charging with the standard charger : 1. Plug the power cord for the charger into the 110/120V outlet. 2. Insert the battery into the charger. The battery fits into the oval recess in only one way. Do not fo...