Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Keep your hands and fingers away from the switch lever (5B) while carrying the trimmer. • Nylon line continues to rotate after the trimmer has been switched off. Before Using Your 12RC 1 .Ensure the battery is fully charged. 2.(4) Adjust the steady handle to a comfortable operating position, by unscrewing the wing knob, springing the side lugs apart, moving the handle to the required position, carefully reengaging the teeth and then tightening the wing knob. (5) To Start Your 12RC 1. Press lock-off button (5A) and squeeze the switch lever (5B). 2. Release the lock-off button (5A). To Stop Your 12RC Release the switch lever (5B). • Automatic Safety Cut-Out (5) An automatic safety cut-out is provided inside your trimmer to protect the motor from overloading. If the trimmer stops, release the switch lever (5B) and wait 30 seconds before attempting to re-start the trimmer. How the automatic line feed works 1 .A short length of new line is fed out every time you start your trimmer, this is caused by the cutting head accelerating up to its full speed. 2.To feed more line, it is necessary to stop your trimmer allow the motor to stop and then restart. Do this frequently when edging. 3.When line feeds you will hear the change in the motor sound together with the noise generated by the line being cut to length. 4. If there is a problem with the Automatic Line feed see Fault Finding Hints, for further information. How to trim and edge • Always wear the eye protection provided. • Do not lean over the trimmer guard whilst trimming or edging objects may be thrown by the cutting line. • Beware of cut-off pieces of nylon line ejected during use. • Nylon line continues to rotate after the trimmer has been switched off. • Do not allow the trimmer cutting head to rest on the ground How to Trim 1 .(6) Cut with nylon line at an angle using the tip. 2.(7) Swing trimmer in and out of the cutting area taking small cuts. 3.Line is fed out automatically every time the trimmer stops rotating or returns to operating speed. How to Edge 1 .(8) To convert to edging mode, depress locking button and twist head anti clockwise until arrow lines up with 'EDGE'. An audible click will confirm that the head is locked. Ensure button has returned to its original position. 2.(9) Rest edger on roller for extra stability and line up with the edge of the lawn. Edge in direction indicated so that debris is thrown away from you. 3.(10) To return to trimming mode depress lock button and twist head clockwise until arrow lines up with 'TRIM'. An audible click will confirm that the head is locked. Ensure button has returned to its original position. Battery care and replacement • Keep your battery fully charged to avoid permanent battery damage. • Dispose of old batteries safely. • Do not cut open, burn or incinerate old batteries. Battery Care 1 .If over a period of time the battery quickly runs down after a full 24 hour charging period, a replacement battery is needed. 2.Contact your local approved service centre/dealer/distributor for a replacement battery and for safe disposal of your old battery . 3.Battery 12 Volt 5 Amp/Hour "High Power" Sealed for Life No maintenance required •IMPORTANT DISPOSE OF YOUR OLD BATTERIES SAFELY DO NOT CUT OPEN, BURN OR INCINERATE. Bench Top Re-charging The wall bracket can also be used as a "bench top" stand for re-charging your 12RC. Winter Storage 1 .Fully charge for 24 hours before winter storage. 2.If you are unable to leave your 12RC on permanent charge, re-charge the battery every 3 to 4 months for a full 24 hour charging period to top up the battery charge during winter storage. 3.Avo¡d extended storage without recharge. 4.Store in a cool dry place. Battery Replacement Should your battery need to be replaced contact your local approved service centre or dealer who will remove your old battery and fit a genuine Husqvarna replacement battery. • IMPORTANT The red lead should always be connected to the red terminal on the battery. The black lead should always be connected to the black terminal on the battery. Spool cap and nylon line • Avoid accidental starting. Keep your hands and fingers away from the switch lever while adjusting, cleaning, or if the nylon line is entangled. • Nylon line continues to rotate after the trimmer has been switched off. To remove Spool Cap 1 .(11) Press and hold in the two cap release latches. 2.(12) Pull cap away from the cutting head. (12) When refitting the spool cap 1 .Keep all areas of the cap and spoolholder clean Failure to do so may prevent the cap being securely located in the spoolholder. 2.Align the two latches on the cap with the two windows in the spoolholder, then press down into the locked position. 3.Ensure the two cap release latches are clearly visible and are fully engaged with the windows in the spoolholder. 4.Check that the cap is correctly fitted by trying to remove it without depressing the two latches...