Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
Lea estas instrucciones de manejo antes de la utilizacion del aparato. BM 2610909755 7/01 1 7/26/01, 12:03 PM 7 6 5 8 4 3 2 1 9 Fig. 1 (Model 1608LX Pictured) (Modele 1608LX illustre) (Modelo 1608LX ilustrado) 7 6 5 8 4 3 2 1 9 Fig. 1 (Model 1608LX Pictured) (Modele 1608LX illustre) (Modelo 1608LX ilustrado) 2 BM 2610909755 7/01 2 7/26/01, 12:03 PM Product Data - Trim Router Base dimensions 3.7" x 2.8" (95mm x 71mm) Collet capacity 1/4" max. Bit diameter 1" max. (NOTE: This tool is designed for use with alternating current (AC) only.) Accessory Listing *STANDARD EQUIPMENT—ALL MODELS 1608M 1608 1608LX 1608T 1608U 1609A 1609AK 1609AKX Steel Case * * 650 Watt Trim Motor * * * * * * * * Wrench 2pcs 2pcs 2pcs 2pcs 2pcs 1pc 2pcs 2pcs Trimmer Base * * * * Laminate Trim Guide * Deluxe Laminate * * Trim Guide Tilt Base * * * Offset Base * * * Underscribe Base * * 4mm Hex Key * * * * 3mm Hex Key * * 1/4 Collet * * * * * * * Collet Nut * * * * * * * Carbide Tipped Bit * * Toothed Belt Pulley * * * Trim Router Components 1. Ventilation openings 11. Adjusting screw - depth of cut 2. Wrench slot 12. Adjusting knob - trim guide 3. Slide "ON/OFF" switch 13. Locking screw - trim guide 4. Motor clamping ring 14. Combination Wrench 5. Collet nut 15. Toothed Belt Pulley 6. Base assembly 16. Offset Base Assembly 7. Sub-base 17. Toothed Belt 8. Clamping ring screw 18. Depth Locking Screw 9. Trim guide assembly 19. Slotted Adjusting Gear 10. Locking knob - depth of cut 20. Wing Nuts (NOTE: components not illustrated on page 2 are illustrated elsewhere in this manual) 3 BM 2610909755 7/01 3 7/26/01, 12:03 PM WARNING! “READ ALL INSTRUCTIONS”. Failure to follow the SAFETY RULES identified by the BULLET (•) symbols listed BELOW and other safety precautions, may result in serious personal injury. Keep these operating instructions with this product. GENERAL SAFETY RULES for all Power Tools Work Area • KEEP WORK AREAS CLEAN. Cluttered areas and benches invite accidents. • AVOID DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations. Do not expose power tools to rain. Keep work area well lit. • AVOID GASEOUS AREAS. Do not operate portable electric tools in explosive atmospheres in presence of flammable liquids or gases. Motors in these tools normally spark, and the sparks might ignite fumes. • KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept away from work areas. Personal Safety • GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces such as pipes, radiators, ranges and refrigerator enclosures. Rubber gloves and non-skid footwear are recommended when working outdoors, where damp or wet ground may be encountered. A Ground Fault Circuit Interrupter protected power line must be used for these conditions. • DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Wear protective hair covering to contain long hair. • USE SAFETY EQUIPMENT. WEAR SAFETY GOGGLES or glasses with side shields. Wear hearing protection during extended use of power tools and dust mask for dusty operations. • STAY ALERT. USE COMMON SENSE. Watch what you are doing. Do not operate tool when you are tired or under influence of drugs. • REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. • AVOID ACCIDENTAL STARTING. Don’t carry plugged in tool with finger on switch. Be sure the switch is OFF before being plugged in. • DON’T OVERREACH. Keep proper footing and balance at all times. • BEFORE CONNECTING THE TOOL to a power supply (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the tool’s nameplate. A power supply with voltage greater than that specified for the tool can result in serious injury to the user—as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power supply with voltage less than the nameplate rating is harmful to the motor. “Volts AC” designated tools are for Alternating Current 50-60 Hz only. “Volts DC” designated tools are for Direct Current. Do not use AC designated tools with DC power supply. Do not use electronic speed controlled tools with DC power supply. Tool Use and Care • DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. • USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purpose not intended—for example; don’t use a circular saw for cutting tree limbs or logs. • SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate the tool. • DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. Always keep cord away from the spinning blade, bits or any other moving part while the tool is in use. • OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only e...