Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Move stop switch button (A) away from the STOP position. 2. Start - Pull Rope. Lay the trimmer on a flat clear area and pull the starter handle (D) until the engine fires. A D NOTE If engine does not start after 5 pulls, use Cold Start Procedure. 18 18 STOPPING ENGINE 1. Release Throttle. Allow engine to idle for a minute. 2. Stop Switch - Stop. Move stop switch button (A) to STOP position. WARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using trimmer again. NOTE Refer to the Grass Trimmer / Brush Cutter Safety Manual for proper and safe trimming techniques. A MAINTENANCE Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your Echo dealer for repairs. SKILL LEVEL Level 1 = Easy to do. Most required tools come with unit. Level 2 = Moderate difficulty. Some specialized tools may be required. Level 3 = Experience required. Specialized tools are required. ECHO recommends that the unit be returned to your ECHO dealer for servicing. ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading are listed the various part numbers required for that task. See your ECHO dealer for these parts. GRASS TRIMMER OPERATOR'S MANUAL19 MAINTENANCE INTERVALS Component/System Maintenance Procedure Daily or Before Use Every Refuel 3 Months or 90 Hours 6 Months or 270 Hours Yearly Air Filter Clean / Replace I / C R * Fuel Strainer Clean / Replace I R Fuel Line Inspect I I I Carburetor Inspect / Rebuild / Replace I / C R (1) Choke System Inspect / Clean / Replace I / C I / C Cooling System Inspect / Clean I / C Muffler Spark Arrestor Inspect / Clean I / C Cylinder Exhaust Port Inspect / Clean / Decarbon I / C Drive Shaft (Flex Cable Models) Grease I (2) Gear Housing Grease I Starter Rope Inspect / Clean I Fuel Leaks Inspect / Replace I I Spark Plug Clean / Replace I / C R Ignition System Clean / Replace No Maintenance required for coil and flywheel Screws/Nuts/Bolts Inspect /T ighten / Replace I I = Inspect / R = Replace / C = Clean Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. (1) Replacement will be required for commercial use yearly. For Consumer use, cleaning every 6 months is required. Cleaning includes Rebuild Kits. * All recommendations to replace are based on the finding of damage or wear during inspection. (2) Grease flexible drive cables every 25 hours and/or on a weekly schedule. 20 20 AIR FILTER Level 1. Tools required: Cleaning brush, 25 or 50 mm (1 or 2 in.) medium bristle paint brush. Parts required: 90008 REPOWERTM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from the air cleaner area. 2. Remove the air cleaner cover. Clean and inspect the element for damage. If element is fuel soaked and very dirty, replace. 3. If element can be cleaned and reused, be certain it: -still fits the cavity in the air cleaner cover. -is installed with the original side out. NOTE Carburetor adjustment may be needed after air filter cleaning/ replacement. See Carburetor Adjustment Section. FUEL FILTER Level 1. Tools required: Fuel line hook, 203-254 mm ( 8-10 in.) length of wire with one end bent into a hook. Clean rag, funnel, and an approved fuel container. Parts required: 90008 REPOWERTM AIR & FUEL FILTER KIT WARNING DANGER Fuel is VERYflammable. Use extreme care when mixing, storing or handling. 1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2. Use the “fuel line hook” to pull the fuel line and filter from the tank. 3. Remove the filter from the line and install the new filter. GRASS TRIMMER OPERATOR'SMANUAL21 WARNING DANGER Catalytic mufflers operate at extremely high temperatures. Muffler area must be kept clean. Do not perform maintenance on the muffler until engine and muffler are completely cool, otherwise serious personal injury may occur. SPARK PLUG Level2. Tools Required: Spark Plug socket wrench and screw driver, Feeler gauge. Preferably a wire gauge. Parts Required: 90064 REPOWERTM Tune-Up Kit 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 145-155 kg/cm (125-135 in. lb.). COOLING SYSTEMS CLEANING Level2. Tools re...