Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
2. GRIP - Rear (right hand) handle. 3. STOP SWITCH - "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD to RUN, BACK to STOP. 4. FRONT HANDLE - The Front (loop) handle is factory assembled to the Drive Shaft assembly but must be repositioned for proper cutting attitude and operator comfort. 5. DRIVE SHAFT ASSEMBLY - Factory Assembled to the Power Head. Includes the Rear (right hand) Handle Assembly, Bearing Housing Assembly, Throttle Trigger, Front (loop, left hand) Handle Assembly, Flexible Drive Cable and Safety Decals. 6. RAPID LOADERTM HEAD - Contains replaceable nylon trimming lines. 7. CUT-OFF KNIFE - Trims line to the correct length (5 in.). If trimmer is operated without a cut-off knife the line will become too long - more than (5 in.) - the operating speed will slow, the engine overheat and performance will suffer. 8. DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife and Safety Decal. Mounts on the Bearing Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming operation. 9. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique. 10. SHOULDER HARNESS - Optional (P/N 99944200201). An adjustable strap that suspends the unit from the operator. 11. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 12. FUEL TANK- Contains fuel and fuel filter. 13. I-30 RECOIL STARTER/HANDLE -i30 spring-assisted recoil starter requires 30% less pulling force than standard recoil starter. Pull handle slowly until starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur. 14. FUEL TANK CAP - Cover and seals fuel tank opening. 15. CHOKE - Located at the rear of the air cleaner housing. Move choke lever to "Cold Start" ( ) to close choke for cold starting. Move choke lever to "Run" ( ) position to open choke. 16. AIR CLEANER - Contains replaceable filter element. 17. PURGE BULB -Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb an additional 4 or 5 times. 18. SPARK PLUG - Provides spark to ignite fuel mixture. GRASS TRIMMER OPERATOR'S MANUAL 9 CONTENTS The ECHO product you purchased has been partially assembled for your convenience. Due to packaging restrictions, installation of the plastic debris shield, nylon line head, and positioning of the front handle are necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. * Some units may be factory pre-assembled. No assembly tools are needed and the nylon line head, plastic debris shield, and mounting hardware, shown in the contents list, are pre-assembled to the unit. Only the front handle may need to be re-positioned for comfortable operation. ____ -Trimmer Assembly: ____ -Power Head ____ -Drive Shaft Assembly ____ -Plastic Bag (Co-Pack) ____ -Operator's Manual ____ -Safety Manual ____ -Warranty Card & Limited Warranty ____ -Locking Tool, P/N 89751801131 (head locking tool) ____ -Safety Glasses ____ -Echo Power Blend TM 2-stroke oil sample ____ -12 pcs. 8 in. x .080 Pre-cut Nylon Line *__ -Rapid LoaderTM 2-line Head *__ -Shield Assembly *__ -Line Head Mounting Hardware: * * ___ -3/8-24 Locknut * ___ -Small Washer * ___ -Large Washer * ___ -Locking Tool, P/N 89751801131 (wrench handle) * ___ -Wrench 17 x 14.5, P/N X602000031 10 10 ASSEMBLY Tools Required: Locking Tools (2), Wrench 17 x 14.5 (9/16 in.) Parts Required: Rapid LoaderTM Head, Large washer, Small washer, 3/8-24 Locknut, (2) Pre-cut Nylon Line 8 in. x .080 in., Plastic Shield Assembly WARNING DANGER Cut-off knife on debris shield has sharp edges. Avoid contact when installing or removing line head. PLASTIC SHIELD INSTALLATION 1. Remove cardboard tube. 2. Remove wing nut (C), washer (B), and bolt (A). 3. Snap the shield over the bearing housing. 4. Install bolt (A), washer (B) and wing nut (C). C B A NYLON LINE HEAD INSTALLATION 1. Remove plastic threaded shaft sleeve from threaded PTO shaft. 2. Align locating hole in upper plate with hole in bearing housing and insert 5 mm (3/16 in.) diameter locking tool (A). 3. Place large washer (B) then line head (C) on threaded shaft, followed by small metal washer (D) and locknut (E). 4. Install 3/8-24 locknut using 14.5 mm (9/16 in.) wrench. Turn locknut clockwise, and tighten securely. IMPORTANT Remember...