Оценок - 6, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Cutting Tools Employ only the correct nylon cutting head for the job in hand. For cutting thick materials, such as weed, high grass, bushes, shrubs, underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work by swinging the string trimmer evenly in half-circles from right to left (similar to using a scythe). Maintenance instructions – The condition of the trimmer also of the shoulder strap must be checked before commencing work. – Turn off the engine and remove the spark plug connector when replacing, and also when cleaning the nylon cutting head. – Operate the string trimmer with as little noise and contamination as possible. In particular, check the correct setting of the carburetor. – Clean the string trimmer at regular intervals and check that all screws and nuts are well tightened. – Never service or store the string trimmer in the vicinity of naked flames. – Always store the string trimmer in locked rooms and with an emptied fuel tank. Observe the relevant accident prevention instructions issued by the relevant trade associations and by the insurance companies. Do not perform any modifications on the string trimmer as this will endanger your safety. The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All the other work is to be done by an Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by DOLMAR. Use of non-approved accessories and tools means increased risk of accidents. DOLMAR will not accept any liability for accidents or damage caused by the use of non-approved nylon cutting heads and fixing devices of nylon cutting heads, or accessories. First Aid In case of accident, make sure that a first-aid box is available in the vicinity of the cutting operations. Immediately replace any item taken from the first aid box. When asking for help, please give the following information: – Place of accident – What happened – Number of injured persons – Kind of injuries – Your name SPECIFICATION SPECIFICATION Model MS-22C Dimensions : length x width x height (without nylon cutting head) mm 1735 x 235 x 220 (68-1/4” x 9-1/4” x 8-5/8”) Mass (without plastic guard and nylon cutting head) kg 3.6 Volume (fuel tank) L 0.4 Engine displacement cc 21.0 Maximum engine performance HP 0.83 /7000 /min Engine speed at recommended max, spindle speed /min 8800 Maximum spindle speed (corresponding) /min 6000 Idling speed /min 3000 Clutch engagement speed /min 4000 Carburetor (Diaphragm - carburetor) type TK TZ9V Ignition system type Solid state ignition Spark plug type NGK BPM7A Electrode gap mm 0.6-0.7(0.024”-0.028”) Fuel Mixed gas (gasoline : two stroke oil = 50 : 1) Gear ratio 14/19 1) The data is prepared taking equally into account the idling and recing or wide open throttle speed operating modes. * WARNING: MODEL MS-22C must not be used with a metal blade. DESIGNATION OF PARTS DESIGNATION OF PARTS . . . . . . . . . . . . .. . MS-22C String Trimmer . . . . . . GB DESIGNATION OF PARTS 1 Fuel Tank 2 Rewind Starter 3 Air Cleaner cover 4 I-O Switch (on/off) 5 Spark Plug 6 Exhaust Muffler 7 Clutch Case 8 Rear Grip 9 Hanger 10 Handle 11 Control Lever 12 Control Cable 13 Shaft 14 Protector 15 Gear Case/Head Case 18 Nylon Cutting Head 20 Fuel Filler Cap 21 Starter Knob 24 Exhaust Pipe ASSEMBLY OF ENGINE AND SHAFT ASSEMBLY OF ENGINE AND SHAFT CAUTION: Before doing any work on the string trimmer, always switch off the engine and pull the spark plug connector off the spark plug. Always wear protective gloves. CAUTION: Start the string trimmer only after having assembled it completely. – Insert the drive shaft into the holder case (Fig). Note: Always insert the drive shaft into the Clutch case fully (approx. 58 mm). If the inner shaft resists full insertion of the drive shaft, try to insert it again after slightly rotating the drive shaft or the support washer on the gear case to match the inner shaft to the hole inside the holder case. – After making sure that the drive shaft is installed fully and properly, tighten the socket head bolt (M5 x 14) and socket head bolt (M5 x 25) to secure the drive shaft. –Inset control cable (1) through adjusting cable (2) and fit nipple of control cable into swivel (3) of carburetor. Connect the switch cords to the two cords from the engine by inserting one into the other. – Fix the cord connector by clamp. Connectors Socket head bolt (M5 x 14) Socket head bolt (M5 x 25) Drive shaft Clutch case MOUNTING OF HANDLE CAUTION: Before doing any work on the string trimmer, always switch off the engine and pull the spark plug connector off the spark plug. Always wear protective gloves. CAUTION: Start the string trimmer only after having assembled it completely. For machine with Loop handle – Do not adjust position of the loop handle too close to the control grip –The standard position of the handle is 200mm to 250mm from the hanger. to engine MOUNTING OF PROTECTOR MOUNTIN...