Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
The wire coloured BROWN must be connected to the terminal marked L or coloured RED. Fuse This apparatus (BS1363). If another adaptor or distribution IF IN DOUBT - CONSULT Batteries Remove the battery cover (18) on the in the direction of the arrows. Insert five the compartment. Take care to ensure all correct polarity as shown inside the battery battery cover. Reduced power, distortion, and a 'stuttering' sound batteries may need replacing. We would recommend for economy, that the SRC985 mains whenever possible with battery operation for occasional stand-by use only. Automatic Mains/Battery switching To change from battery to mains operation, simply plug the mains lead the mains input socket (11) on the rear of the unit. The batteries will be automatically disconnected. It does not matter which way round the plug is inserted but make sure it is fully pushed home. The other end should be plugged into a domestic supply socket. If you need any further advice, please call our Technical Helpline on 020 8758 0338 (Mon-Fri) 4 FM stereo Set the function switch (19) to the (down) position. Adjust The telescopic aerial (14) extended. Carefully tune to If the station being received is Angle and rotate the telescopic A knuckle joint at the base of the aerial of 45 degrees will usually be satisfactory. is accompanied by a high level of background mode by setting the FM mode button (16) The FM band is marked in Megahertz (MHz). function switch (17) to the 'Off/Tape' position. Medium and long wave operation Set the function switch (17) to the 'Radio' position. Select the waveband select switch (19). Adjust the volume control sound is heard. Carefully tune to the desired station using the (20). The unit should be rotated for optimum reception. The MW bands are marked in kilohertz (kHz). To switch off the radio, set the switch (17) to the 'Off/Tape' position. Listening to cassette tapes Set the function switch (17) to the 'Off/Tape' position. Press the stop/eject button (4) to open the cassette compartment (10). Insert a pre-recorded cassette with the tape surface uppermost and the side with the desired recording facing towards you. Close the cassette compartment. Depress the play button (7) and adjust the volume control (13) to suit your personal taste. Use the fast forward (5) or rewind buttons (6) to locate a specific part of the tape. If you wish to temporarily stop the playback depress the pause button (3). When you are ready to resume playback press the pause button a second time. Recording Set the Function station. Adjust the blank cassette with the (8) to commence recording. not affected by the setting Recording from the Internal Set the function switch (17) to the 'Off/with the tape surface uppermost. Press recording. Note : To reduce background noise it is important possible to the internal microphone (1). Caution If the record button will not depress, do not force it. It is probably the cassette tabs have been broken to prevent accidental erasure existing recording. (see preventing accidental erasure) 5 Preventing To safeguard your appropriate tab on the cassette. This will restore the cassette to self-adhesive tape. Safety tab side A Safety tab side B AC60 If you need any further advice, please call our Technical Helpline on 020 8758 0338 (Mon-Fri) ABCD Cleaning the Heads The binder and oxide from magnetic tapes can accumulate on the pinch roller (A) the capstan shaft (B) and also the heads (C and D). This will impair the sound quality. To clean these parts proceed as follows: 1. Turn off the power to the unit 2. Press the Stop/eject button (4) . 3. Press the Play button (7), and the heads will be clearly seen. 4. Clean the surfaces (A, B, C, D) with a lint free rag or cotton swab soaked in alcohol. Press the Stop/eject button as soon as cleaning is over. 6 Specifications Power Requirements Mains : AC 230 volts , 50Hz only Batteries : 5 x IEC LR14 (C size) batteries Circuit Features Loudspeakers Output Power 2 x 75mm dia 8ohms 2 x 1.0 watt RMS Battery Life Approx. 40hrs of listening for 4 hours normal volume, using Alkaline batteries. Headphone socket 3.5mm dia Aerial System FM Telescopic aerial Frequency Coverage FM 87.5 -108MHz MW Built-in Ferrite aerial MW LW 525 - 1620kHz 148 - 284kHz LW Built-in Ferrite aerial Imported by: ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice. 7 Guarantee This instrument or component breakdown, subject or replaced free The guarantee does not 1. Damage resulting from incorrect 2. Consequential damage. 3. Receivers with removed or defaced N.B. Damaged or broken telescopic aerials will Procedure: Any claim under this guarantee should be made through Roberts' dealer will be able to attend to any defect quickly and efficiently, but service department for attention. In the event that it is not possible to return the contact Roberts Radio Technical Services Department at the address shown below ...