Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
" l«BM ” Illuminates. (5) Press the numbered buttons to select the track to be programmed. <5 Press [>/11]. To cancel program play: (From the main unit) Keep [»MEMORY — CLEAR] pressed when CD is in stop mode until "CLEAR” is displayed. (From the remote control) Press [SI/CLEAR] when CD is in stop mode to display “CLEAR”. Pressing [A CD OPEN] will cancel program function. When is displayed: Total play time of the programmed tracks exceeds 100 minutes. Tracks can still be programmed and played. When “FULL” Is displayed: 36 tracks have already been programmed. No further tracks can be programmed. Memory retention of programmed tracks: Track programming is retained even if play is stopped or the unit Is turned off. The display “Cd-P" indicates that programming is retained in the memory. To check programming: While “Cd-P" display is on, dial (h« / V --*■ / A ]. The track number and its play sequence can be checked each time the jog is dialed. RQT4760 ______ Ihevuom g TAPE <► p o_o_ J VOUAS + D CD T ЯРЕ Side to be played back facing up Insert the tape with the exposed tape facing you. t РОГ- ппгI • nr'C- uuu &> =’ Tape travel direction -indicator TRPE 00 I. VOLUME ié m * UL ¡5 ;-3 Listening to Cassettes Types of tapes which can be played on this unit: The unit automatically identifies the type of tape. Normal position/TYPE 1 OK High position/TYPE II OK Metal position/TYPE IV OK Press [POWER 6/1]. (When using batteries for the power supply) Press [® TAPE/CD] to select the cassette mode. TAPE — Cd (The display changes each time the button is pressed.) Press [DECK £], load the tape and close the lid. The direction is automatically set to play the top side (“ E$>” is displayed). Press [REV MODE] on the remote control to select the mode. I (The display changes each time the button Is pressed.) : Both sides are played. (z:) : Both sides play repeatedly until [ffl TAPE/CD] is pressed. : One side is played. Press [«I > TAPE]. “FWD” is displayed and play begins. (“REV” is displayed when play begins while " <£>] "is displayed.) The side which is facing up is played back. <3 : The reverse side is playback. Adjust the volume level. To stop play: Press [0 TAPE/CD]. To stop play from the remote control Press [El]. To listen to the other side of the tape: Press [<3 > TAPE] during playback. • Pressing t> TAPE] automatically turns the unit on, and if a tape is inserted, begins play (only when AC power is supplied). • The volume can be adjusted even in the unit off mode. (Available only from the main unit) The unit cannot be turned on from the remote control when batteries are being used to power the unit. 5 Listening Listening TUNING FF®/ \ \ \ REWlS/\ \ \-/« \ \ Il I» TPL5-i- I Number of tracks skipped Current track Number of times the [ button is pressed Listening to Cesse Wes Fast forwarding and rewinding a cassette 0 Press during stop mode. Rewind Fast forward Main unit REWffPSl FFiTPSl Remote control REW ÍTPS1 [TPSl FF Finding the beginning of a track (TPS: Tape Program Sensor) H_ Press the button once for each track to be skipped (up to 9 tracks). Press during play mode. Backward Forward Main unit REWÍTP51 FFfTPS] Remote control REWÍTPS] ÍTPS1 FF Since the blank spaces between tracks are used for locating the be* ginning of each track, TPS may not operate in the following cases: © When the blank spaces are 4 seconds or less. CD When there are no blank spaces on the tape. (3) When there are parts of a track which have been recorded at a particularly low level or which have not been recorded at all (such as with classical music). © When 10 or fewer seconds have elapsed since the beginning of a track or when there are 10 or fewer seconds until the beginning of the next track. CD When a tape is recorded with fade-ins or fade-outs. To reset the tape counter to "000" El (Available only from the remote control) Press [C-RESET]. Play from this point I FWffiOti R£EE{T C-RESET C-RßET MWffiäjF OtSPUY 1 REVyOOE a lwt o[o 0 0 - VOUME + c :> t Ï <_> ¡ RQT4760 Leader tape (on which nothing can be recorded) Types of tapes which can be used for recording Automatically identifies the type of tape. Normal position/TYPE I OK High position/TYPE II OK Metal position/TYPE IV NO This unit cannot make a recording or erase correctly if metal position tapes are used. To record from the beginning of the tape □ You cannot record on the leader part of the tape. Before recording, wind the tape past the leader to a point where recording can start immediately. To erase a tape □ 1. Load the recorded tape with the side to be erased facing upward. 2. Press [□ TAPE/CD] to select “TAPE". 3. Press [O/O IIREC/REC PAUSE]. Any change made to the volume or sound quality during recording will not affect the recording. In order to prevent trouble caused by flat batteries, it is recommended that you either supply power to the unit from ...