Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
When the tape in the deck which plays first reaches the end of side B (in the reverse direction), it automatically switches to the forward direction and enters the standby mode. At the same time, the other deck starts playback. These operations continue between decks A and B. -5- • While one deck is playing back, the cassette in the other one can be replaced. This is convenient for long-time playback of background music. Note: • Use tapes recorded using the same NR mode in decks A and B. Notes: • When the safety tabs are removed from a cassette tape, the tape cannot be recorded even if you try. Make sure that both tabs are still in place when performing full recording. * When the tape is played or recorded in the reverse direction (side B), only side B is played back or recorded and then the tape stops automatically. RECORDING Deck B only Operate in the order of the numbers in the illustration. • Make sure the safety tab of the cassette has not been broken off. O Turn the power on. © Load a cassette for recording. 0 Set the DOLBY NR switch as required. O Set the REVERSE MODE switch as desired. 0 Select the side to be recorded. © Press the II PAUSE button and #REC/REC MUTE button (record-pause mode). REC and II indicators light. © Adjust the recording level. (See the right column.) © Press to “00 00”. © Press the PLAY button to start recording. It may be unlawful to record or playback copyrighted material without the consent of the copyright owner. DDRP (Dynamics Detection Recording Processor) recording DDRP recording is performed with suitable JVC CD players and the recording level adjustment is performed automatically. Since recording level adjustment is performed automatically for different types of tape (normal, Cr02 and metal), the adjustment of INPUT LEVEL control is not required. Read the instruction book of your CD player carefully. RECORDING LEVEL ADJUSTMENT Adjust the recording level while observing the peak level indica tor indication. For example: With metal tape n -30 20 15 12 10 8 6 ovu 2 0 2 4 6 + 8 dB IL, c=)c=i £=ii=icra <=3 i=i ci=jc=3c=) CZZDC=] a czj trains czntzzi tun i__i tsza R i—il=d c=ic=ic=i<=ii=> i—ii—ii—iod aaoa [=>c=i Because of metal tape’s higher saturation level, it is OK that “+ 2” lights occasionally. With normal or chrome tape L ,= = <=.12 1°<=i.J 2 4 6 + 8 dB It is OK that “+ 0” lights occasionally. • When the recording level is too low, the hiss noise inherent in the tape will be conspicuous. • When the recording level is too high, exceeding the saturation level, the recording will contain cracking noise and will be distorted. • If “+ 4” lights too often because the recording level is too high, the recorded sound may be distorted and seem to be breaking up. If only “0” lights infrequently, the level is too low and the recording may contain tape hiss. It is best to adjust so that the maximum sound level of the source to be recorded reaches the very limit of the saturation level of the tape to be used. The best level varies depending on the type of music and type of tape so it is better to make a test recording, using FM music, records, etc. -6- AUTOMATIC RECORD MUTING (DECK B) This facility is used to eliminate undesired sections and leave an appropriate non-recorded section. A. To leave non-recorded sections of about 4-5 seconds automatically 1. When the undesired section comes during recording, press the • REC/REC MUTE button and release it. 2. The REC indicator flashes and a non-recorded section is made during record muting operation. About 4-5 seconds later, the tape automatically stops, and the unit enters the record-pause mode. 3. Press the PLAY button to start recording again. B. To leave non-recorded sections of more than 4-5 seconds 1. Keep the •REC/REC MUTE button pressed continuously as long as you want to make a non-recorded section. By releasing the finger from the button after the above operation, the unit enters the record-pause mode. 2. Press the PLAY button to start recording again. C. To leave non-recorded section of less than 4-seconds When the undesired section comes during recording.... After the •REC/REC MUTE button is pressed, press the PLAY button before the unit enters the pause mode to start recording again, or press the llPAUSE button to enter the record-pause mode. • The peak level indicator lights even during record muting according to the input level which can be heard from the speakers or headphones so that recording can be resumed at the exact point on the tape. ERASING When recording on a prerecorded tape, the previous recording is automatically erased and only the new program is recorded on the tape. To erase a tape without making a new recording... Follow the section “RECORDING” but in step O, set the INPUT LEVEL control to MIN. DOLBY NR and DOLBY HX PRO Dolby NR System To reduce the hiss inherent in tape recording, use the Dolby NR System when making recordings. When listening...
Эта инструкция также подходит к моделям:Магнитолы - LVT1089-001B (1.54 mb)