Оценок - 6, средний балл: 3.7 ( )

Производитель: Alpine Размер: 454.58 kb Название файла: Язык инструкции:

Align the groove on the front panel with the projection on the main unit. 2 Push the left side of the front panel until it locks firmly into the main unit. 211 Immediately after installing or applying power to the unit, it should be initialized. 1 Press the POWER button to turn off the power. 2 Press the (Release) button to remove the front panel. 3 Using a ballpoint pen or other pointed object, press the RESET switch mounted behind this hole to complete the initialization procedure. RESET Switch 4 Reattached the front panel again. NOTES • The front panel may become hot (especially the connector terminals), this is not malfunction. • Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. NOTE Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. 4-EN Turning Power On and Off 1 Press the POWER button to turn on the unit. NOTE The unit can be turned on by pressing any other button except the eject c button. The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press the POWER button again to turn off the unit. NOTE When the power is turned on for the very first time after the unit is connected to the vehicle's battery, the unit produces sound with the volume level 12, loudness on in the tuner mode. Non Fading Pre-out (N.F.P.) On and Off (TDM-7586RB/TDM-7584R only) 1 Press and hold the Eject (c) button for at least 3 seconds. With each press, N.F.P. is toggled On or Off. N.F.P. ON: In this position, the Pre-Output on the TDM7586RB/ TDM-7584R will not be affected by the fader. This is ideal for driving a subwoofer amplifier. N.F.P. OFF: Returns to normal fader mode. NOTES • Initial mode is N.F.P. OFF. • Set the N.F.P. to OFF unless the subwoofer is used. Adjusting Source Signal Levels If the difference in volume level between the tape player and FM radio is too great, adjust the FM signal level as follows. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the Preset 1 button to select the FM signal level HI (High) or LO (Low) to make the signal levels between the FM band and tape player closer. Each press toggles between FM-LV HI and FMLV LO. 3 Press the SETUP button to cancel the adjusting mode. Adjusting Volume/Bass/Treble/ Balance (Between Left and Right Channels)/Fader (Between Front and Rear Speakers) 1 Press the MODE button repeatedly to choose the desired mode. Each press changes the modes as follows: > VOL > BASS > TREB FAD < BAL < NOTE If the 6 or 5 button is not pressed in 5 seconds after selecting the BASS, TREBLE, BALANCE and FADER modes, the unit automatically sets in the VOLUME mode. 2 Press the 6 and 5 buttons until the desired sound is obtained in each mode. NOTE The settings of the Bass and Treble will be individually memorized for each source (FM, MW, LW, Tape and CD Changer) until the setting is changed. Depending on the connected devices, some functions and display indications do not work. Turning Loudness On/Off 1 Press and hold the LOUD button for at least 2 seconds to activate or deactivate the loudness mode. The display shows "LD" when the loudness mode is activated. 5-EN Radio Operation SOURCE BAND DN g f UP Manual Tuning 1 Press the SOURCE button until radio frequency appears in the display. 2 Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the radio bands as follows: > F1 > F2 > MW > LW 3 Press the TUNE button repeatedly until "DX SEEK" and "SEEK" disappears from the display. NOTE The initial mode is DX-SEEK. 4 Press the DN g or f UP button to move downward or upward one step respectively until the desired station frequency is displayed. NOTE The ST indicator appears on the display when a Stereo FM station is tuned in. If the stereo FM signal becomes weak, the ST indicator disappears from the display and the unit automatically switches the mode from stereo to monaural to reduce the noise. When the signal becomes strong enough, the unit automatically switches back to the stereo mode. Automatic Seek Tuning 1 Press the SOURCE button until radio frequency appears in the display. 2 Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the radio bands as follows: TUNE / A.ME Preset buttons (1 through 6) 3 Press the TUNE button to illuminate the "DX" and "SEEK" indicators in the display. With the DX mode activated, both strong and weak stations will be tuned in the Auto-Seek operation. Press again to return to the local mode. The "DX" indicator will turn off and the "SEEK" indicator will remain illuminated. Now, only strong stations will be tuned. 4 Press the DN g or f UP button to automatically seek a station downward or upward respectively. When the unit finds a station, the unit stops at that station. Press th...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: