Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
23) Wall or Ceiling Mounting — The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24) Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. TASCAM 322 3 Before Getting Started The TASCAM 322 is a double auto reverse cassette deck primarily designed for continuous playback of background music or tape dubbing needs. A maximum of ten 322s can be hooked up to form a sequential play loop or to synchronize them, with one serving as the master/source machine and the others serving as the slave/target machines, for simultaneous tape dubbing. Table of Contents General Guide to the Controls and Connectors ....5 Using a Single 322....................................................9 Recording on either deck, or both at the same time..........................................................9 Continuous recording on both decks....................10 Dubbing from deck 1 onto deck 2 .......................10 Playback...............................................................11 Using just one of the two available decks.......11 Continuous play on both decks.......................11 Using the CPS function........................................12 Erasing recordings................................................12 Multiple-322 System Operation .............................13 Sequential link play..............................................13 Simultaneous dubbing onto multiple cassettes ....14 Recording an external source onto multiple cassettes simultaneously.................................15 Care and Maintenance............................................17 Troubleshooting......................................................18 Error Messages.....................................................18 Specifications .........................................................19 Block Diagram.........................................................20 Optional Accessories : “ LA-322 balanced amplifier kit “ WR-7000 synchro cable (for interconnecting two or more 322s, as shown on pp.12 and 13) “ TZ-261 cleaning kit (except for U.S.A.) “ HC-1 head cleaner & RC-1 rubber cleaner (U.S.A. only) “ Head demagnetizer Rack Mounting The 322 can be installed in a standard 19" rack, using the provided 4 pairs of screws (M5 x 12) and 4 washers, as shown. VOLTAGE CONVERSION NOTE : Voltage conversion is not possible on models sold in the U.K., Australia or Europe. Be sure to remove the power cord from the AC outlet before repositioning the voltage converter switch. 1. Locate the voltage selector on the rear panel. 2. Using a flat-bladed screwdriver, set to the appropriate 230 V or 120 V position according to your area. IN NORTH AMERICA USE ONLY ON 120 V SUPPLY. DANS L’AMERIOUE DU NORD: UTILISABLE SUR 120 V D’ALIMENTATION UNIQUEMENT. 4 TASCAM 322 TASCAM 322 5 General Guide to the Controls and Connectors General Guide to the Controls and Connector s Front Panel 1POWER switch : Turns the unit on and off. NOTE The equipment draws nominal nonoperating power from the ACoutlet with its POWER switch in the OFF position. 2Cassette Compartment : Opens upon pressing the EJECT button. 3RTZ (Return-To-Zero) button : Fast-winds the tape to a zero reference point selected by pressing RESET. You can press PLAY after RTZ for the tape to automatically start playing at the end of the search function. If PAUSE is pressed instead of PLAY, the deck goes into Play Ready mode. The tape will go slightly past the 0000 point on the counter because of inertia. RTZ cannot operate unless it is pressed when the tape counter reads 0003 or higher numbers. 4RESET button : Resets the counter to 0000 to mark any point on the tape which you can access by pressing RTZ. 5EJECT button : Opens the cassette compartment. 6DUAL REC button : If pressed when the tape is stopped, puts both decks into Record Ready mode ; and pressing PLAY on either deck starts recording via deck l’s input. This function is used only for single 322 operation. 7SYNC REVERSE switch : Used for tape dubbing, causing two or more tapes to be switched to their reverse sides in synchronization with each other. 8CPS switch : Can be operated while in Stop, Play Ready, and Play modes to access specific programs on the tape. 9DUB STDBY switches : In NORM mode, you can locate the source tape to the point you want to next start dubbing from, while keeping the target tapes waiting at the end of the previous recording. You can’t do this in HI SPEED mode. APHONES OUT switch : Selects a headphone monitor source. Set to 1 for monitoring tape signals from deck 1, 2 for monitoring tape signals from deck 2, or MIX for monitoring a mix of two tape signals. During Record Ready or Record modes, you can monitor input signals, as selected with this switch. BPHONES control : Adjusts the listening level of the headphones plugged into the PHONES jack. CPHONES jack : For connection to 3-con...