Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
recommends that a qualified person or electrician install this product. Equipment damage, injury to personnel or death could result from improper installation. Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to equipment, or injury or death to personnel that may result from improper installation or operation of this product. WARNING: RISK OF SHOCK OR FIRE - Always use recommended fuse/circuit breaker and wire size. Motors in this product are “Ignition Protected”. They are not however, explosion-proof as defined in 46CFR 110.15-65(e), Subchapter J-Electrical Engineering. WARNING: RISK OF FLOODING-Always shut off seacock(s) before leaving the boat unattended. Whenever possible hose connections should be secured using two stainless steel hose clamps. Integrity of clamps, hoses and fittings should be checked periodically. Crown Head II Sea Water Model Crown Head II Pressurized Freshwater Model The Crown Head II is an automatic electric macerating toilet available in Freshwater or Sea Water flushing. 1-800-352-5630 com Four different Flush Control options are available: 1. Push Button activation - Standard 2. Timed Flush with Push Button - RTC 3. Timed Flush with wall mounted touch pad - TC*+,*specify voltage and +color 4. Momentary Flush with ability to control intake and discharge seperately SWF100 OPERATION • Push Button Switch (#164000) Press and hold switch until all waste is cleared from bowl. NOTE: Push Button Switch flushing is shown. Refer to manuals included with Toilet Control (TC12W), Raritime Solid State Timer with Solenoid (#RTC), or Flush Control (#SWF100) for operation Instructions. • No special toilet paper is required. • Water should appear in the bowl within ten seconds of flushing. If not, see troubleshooting section. • Hard objects or stringy substances (paper towels, feminine hygiene products, filter cigarettes, etc.) must not be thrown into the toilet as they will cause damage. • Always shut off seacock(s) before leaving the boat unattended. Young children should NOT be left unsupervised around toilet. Serious injury or death could occur. WARNING: Children can drown in water retained in the bowl. CAUTION: Seat and/or lid could close and strike child. * Specify Voltage + Specify Color 2 E Cleaning Instructions IMPORTANT: Do not use cleaners that contain ammonia, ethyl acetate, phosphoric acid or concentrated chlorine bleach. These will cause damage to the toilet. Using C.P. (#1PCP22), a bio-enzymatic toilet bowl cleaner (available from Raritan Engineering), will keep the bowl clean and fresh smelling. Recommend Visual Inspection . For leaks at toilet and hose connections . Hose clamps . Condition of hoses . Seacocks . Condition of wires and connections . In-Line Strainer MAINTENANCEC.P. Cleaning In-Line Strainer (Sea Water Models only) 1. Shut off intake seacock. Clean Gasket 2. Unscrew strainer bowl. and Gasket Filter Contact Surfaces 3. Remove filter. Thoroughly 4. Clean bowl and filter with a clean dry cloth. 5. Clean gasket and gasket contact surfaces thoroughly. Bowl 6. Replace gasket, filter and bowl. Unscrew Tighten 7. Open seacock. 8. Check for leaks. 3 G WINTERIZING IMPORTANT • Improper winter lay up is a major cause of marine toilet failure. • Use only nontoxic antifreeze. • Flush toilet several times to clear waste from system. • Dispose of all antifreeze in accordance with local and federal regulations. • Winterize holding tanks, plumbing, treatment systems (MSD’s), etc. independently following manufacturer’s instructions. Sea Water Model Parts Required • 1 1/2" (38mm) I.D. piece of hose, approximately 3 feet (1m) long • 3/4" (19mm) I.D. piece of hose, approximately 3 feet (1m) long • Two buckets • Nontoxic antifreeze approximately 1 quart (1 liter) Steps 1. Close intake and discharge seacocks. 2. Turn off power to unit. 3. Disconnect and drain intake hose, discharge hose and in-line strainer. 4. Connect short hoses to toilet’s intake and discharge. 5. Place one bucket under hose connected to toilet’s discharge. 6. Pour antifreeze in other bucket. 7. Place hose connected to intake pump into bucket with antifreeze. 8. Turn on power to unit and flush until antifreeze is removed from toilet. 9. Disconnect power to toilet. Nontoxic antifreeze 4 • 1 1/2" (38mm) I.D. hose, approximately 3 feet (1m) long • Two buckets • Nontoxic antifreeze approximately 1 quart (1 liter) Steps 1. Close discharge seacock Nontoxic antifreeze 2. Shut off intake water at source. 3. Turn off power to unit. 4. Disconnect and drain discharge hose. 5. Disconnect intake hoses from vacuum breaker and place in one of the buckets. 6. Connect hose to toilet’s discharge and place in the other bucket. 7. Pour antifreeze in bowl. 8. Turn on power to unit and flush until antifreeze is removed from toilet and water is drained from intake lines. Allow water to drain 9. Disconnect power to toilet. into bucket 10. Reconnect intake hoses to vacuum breaker. RECOMMISSIONING ...