2006 Icom Inc. INTRODUCTION This service manual describes the latest service information for the IC-F3061T/S, IC-F3062T/S and IC-F3063T/S VHF TRANSCEIVER at the time of publication. MODEL VERSION SYMBOL CHANNEL SPACING KEY PAD IC-F3061T U.S.A [USA-01] 15.0 kHz/30.0 kHz 10-key IC-F3061S 4-key IC-F3062T EURO [EUR-01] 12.5 kHz/25.0 kHz 10-key IC-F3062S 4-key IC-F3063T GENERAL [GEN-01] 12.5 kHz/20.0 kHz /25.0 kHz 10-key IC-F3063S 4-key To upgrade quality, all electrical or mechanical parts and internal circuits are subject to change without notice or obligation._ DANGER NEVER connect the transceiver to an AC outlet or to a DC power supply that uses more than 7.2 V. Such a connection could cause a fire or electric hazard. DO NOT expose the transceiver to rain, snow or any liquids. DO NOT reverse the polarities of the power supply when connecting the transceiver. DO NOT apply an RF signal of more than 20 dBm (100 mW) to the antenna connector. This could damage the transceiver's front end. ORDERING PARTS Be sure to include the following four points when ordering replacement parts: 1. 10-digit Icom parts number 2. Component name and informations 3. Equipment model name and unit name 4. Quantity required 5030002830 LCD M4-0078TAY-2 IC-F3061T Front unit 5 pieces 8810009220 Screw PH B0 M2x8 ZK (BT) IC-F3061T Chassis 10 pieces Addresses are provided on the inside back cover for your convenience. REPAIR NOTES 1. Make sure the problem is internal before disassembling the transceiver. 2. DO NOT open the transceiver until the transceiver is disconnected from its power source. 3. DO NOT force any of the variable components. Turn them slowly and smoothly. 4. DO NOT short any circuits or electronic parts. An insulated turning tool MUST be used for all adjustments. 5. DO NOT keep power ON for a long time when the transceiver is defective. 6. DO NOT transmit power into a signal generator or a sweep generator. 7. ALWAYS connect a 30 dB to 40 dB attenuator between the transceiver and a deviation meter or spectrum analyzer when using such test equipment. 8. READ the instructions of test equipment thoroughly before connecting equipment to the transceiver. Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. TABLE OF CONTENTS SECTION 1 SPECIFICATIONS SECTION 2 INSIDE VIEWS SECTION 3 DISASSEMBLY INSTRUCTIONS SECTION 4 OPTIONAL UNIT INSTALLATION SECTION 5 CIRCUIT DESCRIPITON 5-1 RECEIVER CIRCUITS........................................................ 5-1 5-2 TRANSMITTER CIRCUITS.................................................... 5-2 5-3 PLL CIRCUITS ............................................................. 5-3 5-4 POWER SUPPLY CIRCUITS................................................... 5-4 5-5 PORT ALLOCATIONS........................................................ 5-5 SECTION 6 ADJUSTMENT PROCEDURES 6-1 PREPARATION............................................................. 6-1 6-2 FREQUENCY ADJUSTMENT.................................................. 6-4 6-3 TRANSMIT ADJUSTMENT.................................................... 6-5 6-4 RECEIVE ADJUSTMENT..................................................... 6-6 SECTION 7 PARTS LIST SECTION 8 MECHANICAL PARTS AND DISASSEMBLY SECTION 9 SEMICONDUCTOR INFORMATION SECTION 10 BOARD LAYOUTS 10-1 FRONT UNIT..............................................................................................................................10-1 10-2 MAIN UNIT................................................................................................................................10-1 10-3 RF UNIT......................................................................................................................................10-1 10-4 JACK UNIT................................................................................................................................10-1 10-5 VR UNIT ....................................................................................................................................10-1 10-6 BC-160........................................................................................................................................10-1 SECTION 11 BLOCK DIAGRAM SECTION 12 VOLTAGE DIAGRAM SECTION 13 BC-160 SECTION 1 SPECIFICATIONS [USA-01], [GEN-01] [EUR-01] GENERAL • Frequency coverage 136-174 MHz • Type of emission Wide 16K0F3E (25.0 kHz/30.0 kHz) 16K0F3E (25.0 kHz) Middle - 14K0F3E (20.0 kHz) Narrow 11K0F3E, 11K0F7E/D* (15.0 kHz) 8K50F3E, 8K10F1E/D* (12.5 kHz) 4K00F1E/D* (6.25 kHz) 8K50F3E (12.5 kHz) 4K00F1E/D* (6.25 kHz) • Number of programable channels 512 channels (128 zones) • Antenna impedance 50 n (nominal) • Operating temperature range -22°F to +140°F -25°C to +55°C • Power supply requirement Spe...
)
