Оценок - 1, средний балл: 4 ( )

Производитель: Icom Размер: 664.7 kb Название файла: Язык инструкции:

DSelective call (DTMF call) q Push [CH Up] or [CH Down], or rotate [ ROTARY SELECTOR* ] to select the LTR system channel or talk group. w Push [DTMF Autodial]— a DTMF encode channel appears. e Push [CH Up] or [CH Down] to select the desired DTMF encode channel. r Push [PTT] to transmit the selected DTMF selected DTMF channel. • Push [DTMF Autodial] to cancel the DTMF transmission. 4 5 5 N ¦ Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. See ( ( . p. 1) ) for accessory attachments. Receiving: q Rotate [VOL] to turn the power ON. w Push [CH Up] or [CH Down], or rotate [ ROTARY SELECTOR]* to select the conventional system channel, in sequence. * Depending on the pre-setting. e When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference. q Push [Call] when initiating a call from your side. • Coded audio may be heard from the transceiver, then “” appears. • This operation may not be necessary depending system. Ask your dealer for details. w While pushing and holding [PTT], microphone at a normal voice level. e Release [PTT] to return to IMPORTANT: To maximize the readability 1. Pause briefly after 2. Hold the microphone your mouth, then voice DTransmitting notes • Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition (‘Inaudible’ condition; “” does not appear.) - The channel is busy. - Un-matched (or matched) CTCSS is received. ( Depending on the pre-setting. ) - The selected channel is a ‘receive only’ channel. • Time-out timer After continuous transmission for the pre-programmed period, the time-out timer is activated, causing the to stop transmitting. • Penalty timer Once the time-out timer is activated, transmission inhibited for a period determined by the DTX code channel selection DTX code channel selection USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select]— a TX code channel number (or name) appears. w Push [CH Up] or [CH Down] to select the desired TX code channel. e Push [Call] (or [PTT] during MSK operation) to transmit the selected TX code. r Push [TX Code CH Select] again to return to the operating channel number indication. USING [TX CODE CH UP]/[TX CODE CH DOWN] If the transceiver has a [TX Code CH Up] Down] key assignment, the programmed TX code channel can be selected directly when pushed. CONVENTIONAL OPERATION 5 DDTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. Up to 8 DTMF channels are available. TO SELECT A TX CODE: q Push [DTMF Autodial]— a DTMF channel appears. w Push [CH Up] or [CH Down] to select the desired DTMF channel. e Push [DTMF Autodial] to transmit the DTMF code in the selected DTMF channel. 5 5 5 ¦ User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “customize” the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [P1] and [P2], rotate [VOL] to turn the power ON. Then, push and hold [P0] to enter user set mode. w Push [P0] several times to select the appropriate item. Then push [Side2] or [Side3] to set the desired level/condition. • Available set mode functions are Backlight, LCD contrast, Beep, Beep Level, Ringer Level, SQL Level, AF Min Level, Mic Gain, VOX Gain, VOX Delay, Battery Voltage and Signal Moni. e Rotate [VOL] to turn the power OFF to exit NOTE: User set mode is also available via key. Please refer to ( ( . p. 9) ) [User Set Mode] section. ¦ Emergency transmission When [Emergency Single] or [Emergency Repeat] is pushed, an emergency signal is automatically transmitted for the specified time period. When [Emergency] is pushed, the DTMF emergency signal is transmitted on the priority channel. When [Emergency Single] or [Emergency Repeat] is pushed for the specified time period, the DTMF emergency signal is transmitted once or repeatedly on the emergency channel. However, when no emergency channel is specified, the signal is transmitted on the previously selected channel. ¦ Scrambler function The voice scrambler function provides private between stations. The frequency inversion type is equipped to all versions, moreover, the optional Rolling or Non-rolling type can be available. q Push [Scrambler] to turn the scrambler • “ ” appears. w Push [Scrambler] again to OFF. • “ ” disappears. CONVENTIONAL OPERATION 5 ¦ Stun function When the specified ID, set as a killer ID, is received, the stun function is activated. When the killer ID is received, the transceiver switches to the password required condition. Entering of the password via the keypad is necessary to operate the transceiver again in this case. ¦ Priority A channel selection When one of the following operations is performed, the select...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: