Оценок - 4, средний балл: 3.8 ( )

Производитель: Icom Размер: 555.95 kb Название файла: Язык инструкции:

Turn the power off and start over in this case. DBattery type selection The battery type must be selected battery type when turning the transceiver Ask your dealer for details. q Turn the power OFF. w While pushing and holding [Emer] and [PTT], power ON with rotating [VOL] to toggle the attaching type. • After the display appears, release [Emer] and [PTT]. • “DRY BATT” is displayed for about 3 sec. then “ L” appears when the battery case operation is selected. In this case, the transmit output power is low. • “LI-ION” is displayed for about 3 sec. when the Lithium-ion battery operation is selected. Appears [VOL] [Emer] [PTT] Dry battery mode 11 BASIC OPERATION 3 3 Channel selection Several types of channel selections are available. Methods may differ according to your system set up. NON-ZONE TYPE: Push [CH Up] or [CH Down] to select the desired operating channel, in sequence; or, push one of [MR-CH 1] to [MR-CH 4] keys to select a channel directly. ZONE TYPE: Push [Zone], then push [CH Up] or [CH Down] to select the desired zone. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. Call procedure When your system employs tone signaling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signaling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2-tone code according to your System Operator’s instructions. • This may not be necessary depending on programming. • Refer to page 13 for selection. w Push the call key (assigned to one of the dealer programmable keys: [Emer], [Side1], [Side2], [Side3], [P0], [P1], [P2] and [P3]) or [PTT]. eAfter transmitting a 2-tone code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling 3 Receiving and NOTE: Transmitting without an antenna transceiver. See page 1 for accessory Receiving: q Rotate [VOL] to turn the power ON. w Push [CH Up] or [CH Down] to select the channel, in sequence. e When receiving a call, adjust the audio output comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference. q Push [Call] when initiating a call from your side. • Coded audio may be heard from the transceiver, then “” appears. • This operation may not be necessary depending on your signaling system. Ask your dealer for details. w While pushing and holding [PTT], speak into the microphone at a normal voice level. e Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your signal; 1. Pause briefly after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. DTransmitting notes • Transmit inhibit function The transceiver has several inhibit transmission under the following conditions: - The channel is in mute condition (‘Inaudible’ condition; “ ” does not appear.) - The channel is busy. - Un-matched (or matched) CTCSS is received. ( Depending on the pre-setting. ) - The selected channel is a ‘receive only’ channel. • Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer is activated, causing the transceiver to stop transmitting. • Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. DTX code channel selection DTX code channel selection USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select]— a TX code channel number (or name) appears. w Push [CH Up] or [CH Down] to select the desired TX code channel. • Push [TX Code CH Select] again to return to the operating channel number indication. e Push [Call] to transmit the selected TX code. USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY: If the transceiver has [TX Code CH Up] or [TX Code CH Down] assignment, the programmed TX code channel can be selected directly when pushed. BASIC OPERATION 3 DDTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the DTMF transmission function channels are available. TO SELECT A TX CODE: q Push [DTMF Autodial]— a DTMF channel appears. w Push [CH Up] or [CH Down] to select the desired DTMF channel. e Push [DTMF Autodial] to transmit the DTMF code in the selected DTMF channel. 3 3 3 User set mode User set mode is accessed set seldom-changed settings. the transceiver operation operating style. Entering the user set mode: q While pushing and holding [Side2] and [Side3], [VOL] to turn the power ON. Then, push and hold [P0] for 1 sec. to enter user set mode. w Push [P0] several times to select the appropriate Then push [CH Up] or [CH Down] to set the desired level/condition. • Available set mode functions are Backlight, Beep, Beep Level, SQL Level, Mic Gain, Battery ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: