Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
BATTERY SAVER The transceiver provides a battery saver mode to conserve on battery power. The transceiver will activate the battery saver circuit 10 seconds after the last key operation with the squelch closed. The function will be released by key operation or when squelch opens. The function cannot operate during scan or tone light • Timing chart ON OFF H-H«-*H 150mS 800mS When DTSS function is ON. ON OFF -H—H-h*- 150mS 100mS 4-10. AUTOMATIC POWER OFF This transceiver also provides an Automatic Power OFF circuit. The circuit action is described below. (Initial state is ON.) 1. A 5 second audio confirmation alert will sound after 59 minutes if no signal has been received and if you have not performed any operation. 2. 1 minute after this alert signal the transceiver will shut itself off except for enough power to show “APO” in the display. 3. When the APO operates and the transceiver is shut off after 60 minutes, the transceiver can be reactivated by pressing the MONI switch, or by turning the POWER switch OFF and back ON. 4. To turn the APO function OFF/ON, press the CALL key while turning on the POWER switch._ Note The function can not be activated during scan or Tone Alert system operation. To conserve battery life even more simply turn the transceiver OFF when you are not using it. 37 4-11. DTMF MEMORY FUNCTION [ With DTMF KEY PAD DTP-1 (Option) and DTMF UNIT DTU-1 (Option)] Four different DTMF telephone numbers, of up to a maximum of 15 digits, can be memorized. The function can be activated by pressing the * key while turning the POWER switch ON. Channels from 1 through 15 will then be used for storing frequency data and channels 16 ~ 20 will be used to store telephone number data. The function can be turned off by pressing the # key while turning the POWER switch ON. Note The contents of channels 16 ~ 20 will be erased. • Storing the DTMF codes 1. Press the * key while turning O CD ON the POWER switch. 0 2. Press the * key within 10 seconds of pressing the F p- - . key. The display will show the following (see right). 3. Enter the DTMF code on the ten key (up to a maximum of 15 digits)._ Notes 1. If you enter the wrong number, start again. 2. If you want to stop the entry midway, press the # key. The previously displayed frequency will reappear on the display. 38 4. When the DTMF code has been entered, select the channel (A, B, C, D) where you want to store the DTMF code and press the key for that channel. When the DTMF code is stored to that channel, the previously shown frequency will reappear on the display. (Ex. Channel A) • Making a DTMF call To transmit: Press the key for the channel (A, B, C or D) where you stored the DTMF code in receive mode. The display will show the following (see right). (Ex. Channel A) Then press the PTT switch within 10 seconds to switch to the transmit mode. The DTMF code will be output and the previously shown frequency will reappear on the display. A CD A CD Notes 1. While the stored DTMF code is recalled, transmission continues until the whole code string is recalled even if the PTT switch is released. 2. If you want to stop output of the stored DTMF code midway, release the PTT switch once and then press it again. • Recalling stored DTMF code in receive mode Press the F key and within 10 seconds press the A, B, C or D key. The DTMF code stored in the key will be output to the display. The code is displayed from right to left as illustrated. To cancel the display halfway, press any key. p- /Эта инструкция также подходит к моделям:
Лодочное оборудование - TH-26A (6.31 mb)
Лодочное оборудование - TH-46A (6.31 mb)
Лодочное оборудование - TH-46E (6.31 mb)
Лодочное оборудование - TH-66AT (6.31 mb)