Оценок - 2, средний балл: 3.5 ( )

Производитель: Garmin Размер: 2.29 mb Название файла: Язык инструкции:

Use at least 22 AWG wire for extended runs of wire, if needed. GHS 10 Cable W GHS 10 Cable WGHS 10 Cable Wiring-Assignment T iring-Assignment Tiring-Assignment Table ableable NotICe: Cover the connections with a waterproof, adhesive tape, such as rubber vulcanizing tape, to prevent water from seeping into the radio. Installing the Bulkhead Pass-Through Plate 1. Route the GHS 10 active speaker cable (or the GHS 10 cable) to the location you want to install the bulkhead pass-through plate. 2. Drill a 1 in. (25 mm) hole in the location at which you want to pass through the bulkhead. 3. Place the bulkhead pass-through plate over the hole and mark the three pilot-hole locations. 4. Drill the three 1/8 in. (3 mm) pilot holes.* 5. Connect the bulkhead pass-through plate to the bulkhead using the included M3.5 . 20 mm pan-head screws. 6. Remove the nut and connector cover from the GHS 10 cable (or the active speaker cable) and feed the connector through the bulkhead pass-through plate. 7. Place the GHS 10 connector cover over the connector. 8. Use the nut to fasten the connector to the bulkhead pass-through plate. . . . . . . . . To the VHF 300 series transceiver box, or to the active speaker (cable dependent) . To a passive speaker (GHS 10 cable only) . Bulkhead . Bulkhead pass-through plate . GHS 10 connector cover . Nut . M3.5 . 0 mm screws Installing the Bulkhead Pass-Through Plate Mounting the GHS 10 Hanger Using the GHS 10 hanger as a template, mark and drill 1/8 in. (3 mm) pilot holes.* Use three of the included 3.5 . 20 mm, panhead mounting screws to mount the hanger in a convenient location near the bulkhead pass-through plate. Connecting the GHS 10 After you install the bulkhead pass-through plate and the GHS 10 hanger, connect the GHS 10 to the connector on the bulkhead pass through plate. Hang the GHS 10 on the GHS 10 hanger. Connecting the VHF 300 Series Radio to a Chartplotter (Optional) You can connect the VHF 300 series radio to a chartplotter so that data such as DSC information can be displayed on the chartplotter. Additionally, the radio can use location information from the GPS function of the chartplotter for position reports, and so forth. You can connect the VHF 300 series radio to a NMEA 2000 network to access a NMEA 2000-compatible GPS antenna or chartplotter, or you can wire the radio directly to a NMEA 0183-compliant chartplotter. * A 1/8 in. (3 mm) pilot hole is nominal for plywood. Different dashboard materials my require a different size pilot hole. VHF 300 Series Installation Instructions VHF 300 Series Installation Instructions Connecting the VHF 300 Series Radio to a NMEA 2000 Network You can connect the VHF 300 series radio to your existing NMEA 2000 network, or you can build a basic NMEA 2000 network to connect to another NMEA 2000-compatible device, such as a chartplotter. For more information on NMEA 2000 and to purchase required connectors, go to To connect the VHF 300 series radio to your existing NMEA 2000 network: 1. Determine where you would like to connect the radio to your existing NMEA 2000 backbone. 2. Disconnect one side of a NMEA 2000 T-connector from the backbone at an appropriate location. If you need to extend the NMEA 2000 backbone, connect an appropriate NMEA 2000 backbone extension cable to the side of the T.connector you disconnected. 3. Add a T.connector (not included) for the radio to the NMEA 2000 backbone by connecting it to the side of the T.connector you disconnected. 4. Route a NMEA 2000 drop cable (not included) to the bottom of the T.connector added in step 3 to your NMEA 2000 network. Use a drop cable with a length up to 20 ft. (6 m). 5. Connect the drop cable to the T.connector and the NMEA 2000 port on the VHF 300 Series transceiver box. Notice: If you have an existing NMEA 2000 network on your boat, it should already be connected to power. Do not connect an additional NMEA 2000 power cable to an existing NMEA 2000 network, because only one power source should be connected to a NMEA 2000 network. . VHF 300 series transceiver box . NMEA 2000 device (not included) . Drop cable (not included) . T-connector (not included) . Existing NMEA 2000 network . Ignition or in-line switch . Fuse . 12 Vdc battery . NMEA 2000 power cable (not included) . Terminator (not included) Creating a Basic NMEA 2000 Network + - . . . . . . . . . . . . . . . . Connecting the VHF 300 Series Radio to an Existing NMEA 2000 Network VHF 300 Series Installation Instructions To create a basic NMEA 2000 network: 1. Connect two T-connectors (not included) together by their sides. 2. Connect a NMEA 2000 power cable (not included) to one of the T-connectors. notice: A NMEA 2000 power cable must be connected to a 12 Vdc power source through a switch. The NMEA 2000 network may drain your battery if it is connected directly. Connect the cable to the ignition switch of the boat if possible, or through an appropriate additional switch. 3. Connect a NMEA 2000 drop cable (not i...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: