Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Contrast is controlled by the 8 and 9 keys. DISPLAY: This page is only displayed if manual backlighting mode is selected during installation configuration. Backlighting is controlled by the 8 and 9 keys. ADS-B: This page is displayed if the ADS-B pilot set option is selected during installation configuration of an ES enabled GTX 330. ADS-B defaults to ON at each power cycle. ADS-B ON/OFF is controlled by the START/ STOP key. Turn ADS-B OFF only at the request of ATC. Altitude Trend Indicator When the PRESSURE ALT page is displayed, an arrow may be displayed to the right of the altitude, indicating that the altitude is increasing or decreasing. One of two sizes of arrows may be displayed depending on the vertical speed rate. The sensitivity of these arrows is initially set during transponder installation. Timer Operation To operate the Flight Timer: 1) Press the FUNC key until FLIGHT TIME is displayed. 2) If the GTX 330 is configured with Automated Airborne Determination, the timer begins automatically when the unit senses that the aircraft has become airborne. The timer may be reset to zero at every take off, continue accumulating time at take off, or may be controlled manually. 3) If desired, press START/STOP to pause or restart the timer. 4) Press CLR to reset the timer to zero. 5) If the timer is configured to start automatically it will stop when the Automated Airborne Determination senses that the aircraft is on the ground. To operate the Count Up timer: 1) Press the FUNC key until COUNT UP is displayed. 2) If necessary, press CLR to reset the Count Up timer to zero. 3) Press START/STOP to begin count up. 4) Press START/STOP again to pause the timer. 5) Press CLR to reset the timer to zero. To operate the Count Down timer: 1) Press the FUNC key until COUNT DOWN is displayed. 2) Press CRSR and use the 0 - 9 keys to set the initial time. All digits must be entered (use the 0 key to enter leading zeros). 3) Press START/STOP to begin count down. 4) Press START/STOP again to pause the timer. 5) When the Count Down timer expires, the COUNT DOWN banner is replaced with a flashing EXPIRED, the message “Timer Expired” is heard, and the time begins counting up. 6) Press CLR to reset the timer to the initial time value. Automatic ALT/GND Mode Switching If the GTX 330 is configured for Automated Airborne Determination, normal operation begins when take off is sensed. When the aircraft is on the ground the screen automatically displays GND. The transponder does not respond to ATCRBS interrogations when GND is annunciated. When a delay time is set (dependent upon installation configuration), the GTX 330 waits a specified length of time after landing before changing to GND mode. Failure Annunciation If the unit detects an internal failure, the screen displays FAIL. When FAIL is annunciated no transponder data is transmitted. Mode S Data Transmission In addition to 4096 code and pressure altitude, the GTX 330 is capable of transmitting aircraft identification, transponder capability, and maximum speed range. Aircraft identification is commonly referred to as FLT ID (Flight Identification). The GTX 330 may be configured by the installer to allow the flight crew to enter FLT ID for each flight. An example is when air-carrier service requires changing the FLT ID. The FLT ID may consist of the aircraft registration or a flight number as agreed upon with the local aviation authority. In either case, the FLT ID must be the same aircraft identification that appears in the flight plan to correlate the aircraft identification seen on ATC radar with the correct voice call sign for the aircraft. If no flight plan is filed with the aviation authority (as may be permitted by regulations), the FLT ID entered is the aircraft registration marking. When flight crew entry of the FLT ID is not required, the installer configures the system to report the aircraft identification according to local aviation requirements. In this configuration, alteration of the FLT ID by the flight crew is not possible. Altitude Monitor Operation To operate the Altitude Monitor: 1) Climb to assigned altitude. 2) Press the FUNC key until ALT MONITOR is displayed. 3) Press START/STOP key to start monitoring altitude. 4) Press START/STOP key again to cancel Altitude Monitor. Altitude deviation is shown in hundreds of feet ABOVE or BELOW the selected altitude. When the aircraft’s altitude exceeds the deviation limit, ABOVE or BELOW flashes and an audio tone or the message “Leaving Altitude” is heard. ABOVE or BELOW flashes until the aircraft returns to within 100’ of the selected altitude. To select a new monitored altitude, press the START/STOP key to deactivate, then press again to activate the new monitored altitude. If another function is selected for viewing, such as a Timer or Pressure Altitude, the Altitude Monitor is automatically displayed with a flashing alert when the altitude excursion exceeds the configured deviation value. The Altitude Monitor sto...
Эта инструкция также подходит к моделям:Лодочное оборудование - GTX 330 (351.94 kb)