Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69383 Rev. B 03-10 FEATURES The Attwood 12-Volt, 1-Mile Navigation Combination Lights for boats up to 39.6 ft. (12 meters) incorporate a separately switched Task Light. They feature impact resistant, UV-stable polycarbonate housings. Certification: Bi-Color, 12-Volt, Sidelight with Tasklight. Meets USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards as tested by Imanna Labs on 1/13/2003. 1 Nautical Mile visibility. Uses 9235 #906 Lamp, 13V, 6 Candle Power. REQUIRED FOR INSTALLATION • Cordless drill with 1/8" (3mm), 3/8" (10mm) and 3/4" (19mm) bits. • Screwdriver. • Three #8 or #10 stainless pan head screws per light. • Non-silicone sealant. WARNING: To prevent personal injury, always disconnect the power source when installing or servicing this product. Always remove the boat from the water before using 120V AC power tools. LOCATION Lights must be mounted to an unobstructed smooth surface on the gunwale, deck or superstructure. Locate Bi-Color Combination Light in an area as far forward as possible. (Figure 1) STANDARD 3-PIN BASE WIRING CONFIGURATION For proper operation, the base that will accept the pole light must be wired as in Figure 2. Figure 1 Figure 2 Red Green To +12-Volt Navigation Light Switch White To +12-Volt • •• To -12-Volt Circuit with Fuse Battery (Powered Constantly) POLE LIGHT INSTALLATION CAUTION: All positive (+12V DC) wires must be fused to protect your circuits and vessel. The Combination Light requires a 1-amp fuse. The Task Light requires a 1-amp fuse and separate wire circuit. The aluminum pole of the Universal Fit Light is not connected to an electrical ground. (Figure 2) 1. Insert pole into base, aligning screw with slot in base. 2. Press down firmly to engage electrical connectors. 3. Slide locking collar down to base, rotate until lower ring can be inserted inside top of base. 4. Press down into base and rotate until locking collar tightens between pole and base. NOTE: Periodically check pole to make sure it is secure. 5. To remove light, rotate locking collar in opposite direction until it loosens, then pull up on pole. (Figure 3) After installation, activate lights to verify proper operation. Navigation light regulations require lights to be operated with a three-position switch that provides for: • Running lights (combination light and all-round light). • Anchor lights (all-round light only). • Off. • Check the Task Light by pressing on switch at rear of light to turn Task Light on. (Figure 4) Figure 3 Locking Collar Lower Ring Screw • • • NOTE: Navigation light poles are designed to support only the light. They should never be used as flag poles or handles. MAINTENANCE When not in use, always store pole light in Pole Light Storage Clips (Attwood 7571). Choose a storage location where it will not be damaged or be in constant contact with water. Close the base cover when light is stowed to protect the contacts and seal the deck. Replacing Bulb 1. Twist lens helmet 1/4 turn counter-clockwise to remove. 2. Replace Navigation Light bulb with 9-Watt Wedge Base Replacement Bulb (Attwood 9235). 3. Re-seat lens helmet and twist 1/4 turn clockwise until it clicks in place. (Figure 4) Task Light lamp is not serviceable. Clean the light with a mild soap and warm water solution. Never use solvents or abrasives that may damage the lens or housing of the Universal Fit Light. Figure 4 On Off • • • • • Lens Helmet Bulb #906 Lens Bayonet Channels Press Here Task Light Bulb ATTWOOD LIMITED WARRANTY ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”) warrants to the original consumer purchaser that Attwood brand products will be free from defects in materials and workmanship under normal use and service for one year from the date of original consumer purchases. This limited warranty is not applicable if the product has been damaged by accident, improper installation, unreasonable or improper use, lack of proper maintenance, unauthorized repairs or modifications, normal wear and tear, or other causes not arising out of defects in materials or workmanship. Attwood products are warranted for use on pleasure boats. Any other use — including but not limited to commercial, racing, or non-marine use — are not covered under this warranty. Attwood’s obligation under this warranty is limited to repair of the product at Attwood’s plant or replacement of the products at Attwood’s option without expense to the original consumer purchaser. Any expenses involved in the removal, reinstallation or transportation of the product are not covered by this warranty. The product must be returned to Attwood’s plant at the address above, postage prepaid, and insured with proof of original purchase including date. If Attwood is unable to replace the product and repair is not commercially practical or cannot be timely made, or if the original consumer purchaser is willing to ...