Оценок - 5, средний балл: 4.4
(
)
)
|
Фото и характеристики Furuno CH-37 |
Фрагмент инструкции
.. 1998 19981998 P PPr rrinte inteinted in J d in Jd in Ja aapa papan nn E2 E2E2 : :: JU JUJUL LL. .. 28, 28,28, 2006 20062006 P PPub. ub.ub. No. No.No. I IIM MME EE- --13030- 13030-13030-E EE2 22 A AAll r ll rll ri iig ggh hht tts r s rs re eese seser rrv vve eed dd. .. * **0 000080821301*0080821301* 0080821301* ( (( HI HIHIM MMA AA ) )) CH- CH-CH-37 * **3737 0 000080821301* 0080821301*0080821301* * ** 0 0 0 8 0 8 2 1 3 0 1 * 0 0 0 8 0 8 2 1 3 0 1 *0 0 0 8 0 8 2 1 3 0 1 * * **I IIME MEME1 113030E20* 3030E20*3030E20* * **I IIME MEME1 113030E20* 3030E20*3030E20* * ** I II M MM E EE 1 3 0 3 0 E 1 3 0 3 0 E1 3 0 3 0 E 2 0 * 2 0 *2 0 * SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment unless totally familiar with electrical circuits and service manual. Only qualified personnel should work inside the equipment. Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water splash. Water in the equipment can result in fire, electrical shock or equipment damage. Be sure no water leaks in at the transducer installation site. Water leakage can sink the vessel. Also confirm that the transducer will not loosen by ship's vibration. The installer of the equipment is solely responsible for the proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with improper installation. WARNING Install the specified transducer tank in accordance with the installation instructions. If a different tank is to be installed the shipyard is solely responsible for its installation, and it should be installed so the hull will not be damaged if the tank strikes an object. The tank or hull may be damaged if the tank strikes an object. If a steel tank is installed on a wooden or FRP vessel, take appropriate measures to prevent electrolytic corrosion. Electrolytic corrosion can damage the hull. Be sure that the power supply is compatible with the voltage rating of the equipment. Connection of an incorrect power supply can cause fire or equipment damage. The voltage rating of the equipment appears on the label above the power connector. CAUTION Ground the equipment to prevent electrical shock and mutual interference. Observe the following compass safe distances to prevent deviation of a magnetic compass: Display unit Standard compass 2.2 m 1.6 m Steering compass WORKING WITH THE SONAR OIL Precautions · Keep oil away from eyes. Wear protective gloves when working with the oil. The oil can cause inflammation of the eyes. · Do not touch the oil. Wear protective gloves when working with the oil. The oil can cause inflammation of the skin. · Do not ingest the oil. Diarrhea or vomiting can result. · Keep the oil out of reach of children. Emergency · If the oil enters eyes, flush with clean water about 15 min. Consult a physician. · If the oil contacts skin, wash with soap and water. · If the oil is ingested, see a physician immediately. Disposal of oil and its container Dispose of oil and its container in accordance with local regulations. For further details, contact place of purchase. Storage Seal container to keep out foreign material. Store in dark place. TABLE OF CONTENTS EQUIPMENT LISTS ................................................................................................... iv SYSTEM CONFIGURATION ................................................................................... v MOUNTING 1.1 Hull Unit ..................................................................................................................... 1-1 1.2 Transceiver Unit ...................................................................................................... 1-13 1.3 Display Unit ............................................................................................................. 1-14 1.4 Grounding the Display Unit and Transceiver Unit ................................................... 1-14 1.5 Motion Sensor MS-100 (Option) ............................................................................. 1-15 1.6 External Interface (Option) ...................................................................................... 1-15 1.7 Logarithm Amplifier Video Sounder ........................................................................ 1-17 1.8 Clinometer BS-704 (option)..................................................................................... 1-19 WIRING 2.1 Wiring Among Units................................................................................................... 2-1 2.2 Synchronizing Transmission with Echo Sounder or Other Sonar ............................. 2-4 ADJUSTMENTS 3.1 General Checks ........................................................................................................ 3-1 3.2 Adjustment of Transceiver Unit .......................................................