Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
See or Product Catalog for details. CAUTION: Read all instructions carefully before installing and using this product. This pump is sealed and, therefore, submersible. However, the electrical wire connections must not be submerged. For extra protection, coat the butt joints and adjacent wire ends liberally with liquid electrical tape such as MDR® or Starbrite®. Specifications ABYC Specifications ISO Specifications 13.6-volts DC 12.0-volts DC (GPH=Gallons Per Hour) (LPH=Liters Per Hour) 0 ft. 3.3 ft. 6.7 ft. 10kPa 20kPa Head Head Head Head Head Max Head Part Amp GPH/ GPH/ GPH/ LPH/ LPH/ (ft.@13.6v/ Num. Model Fuse amps amps amps amps amps kPa@12v) 4505 S500 2.0 500/1.5 350/1.4 200/1.4 1136/1.2 598/1.2 9'/24 4507 S750 5.0 750/3.0 625/2.8 450/2.8 1817/2.5 1306/2.5 16'/36 4511 S1100 6.0 1100/4.0 970/3.8 750/3.8 3104/3.3 2328/3.3 11'7"/28 WARNING: To prevent injury, always disconnect the power source when installing or servicing any electrical product. DO NOTuse pump to remove gasoline, oil or other flammable liquids. Always use the fuse amperage rating specified for your pump model. Failure to do so could result in serious personal injury or fire hazards. Attwood bilge pumps are designed to exhaust STANDING WATER ONLY.They are not intended to prevent rapid accumulation of on-board water due to rough weather, hull damage, and/or other unsafe navigational conditions. REQUIRED MATERIALS • Hose and thru-hull fittings, available separately from Attwood: Sahara Model 4505 and 4507– 3/4" I.D. hose: Attwood No. 4199 (includes 2 clamps) 3/4" I.D. thru-hull: No. 3873 (straight), No. 66541 or 66547 (stainless steel straight), No. 3877 (90°), or No. 3878 (double-end) Sahara Model 4511– 1-1/8" I.D. hose: No. 11551 (clamps not included) 1-1/8" I.D. thru-hull: No. 3874 (white), No. 3874A (black) or No. 66543, 66549 (stainless steel), or No. 3879 (90°) • Two (2) hose clamps suitable for (3/4" or 1-1/8") hose. • AUTO/OFF/MANUAL dash-mounted control switch (Attwood No. 7615A). • In-line fuse connector (Attwood No. 14341) and appropriate size fuse. • Three (3) stainless steel #6 x 1/2" self-tapping screws, round or pan head. Use a #32 drill bit for pilot holes. • Four (4) wire butt-connectors for 16-gauge wire. • Two (2) insulated spade terminal connectors for 16-gauge wire. • Suitable means to make electrical connections waterproof. • Cordless drill. • Screwdriver. • 1/2"-thick marine plywood block (slightly larger than pump base). • Waterproof adhesive (epoxy, silicone adhesive, or fiberglass resin) to mount block. • 16-gauge wire (brown and black). PUMP MOUNTING INSTRUCTIONS WARNING: Remove the pump mounting base (See Figure 3). Remove the foam block that supports the float during shipping. Failure to do this prevents the pump from starting when water is present. 1. Make sure the hull thickness is at least 1/2" thick. If not, place a block of 1/2" marine plywood (slightly larger than pump base) in the lowest part of the bilge. Be sure that the p...
Эта инструкция также подходит к моделям:Лодки - Sahara 4505-1 (466.79 kb)
Лодки - Sahara 4505MP1 (466.79 kb)
Лодки - Sahara 69370 (466.79 kb)