Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Turning the ignition switch to the OFF position stops the engine. CONTROLS AND FEATURES Switch Clip and Emergency StopSwitch EMERGENCY STOP SWITCH \ LANYARD I ” SWITCH CLIP The switch clip must be inserted in the emergency stop switch in order for the engine to start and run. The lanyard must be attached to the operator’s PFD (Personal Flotation Device) or worn around the wrist as shown. When used as described, the emergency stop switch and lanyard system stops the engine if the operator falls away from the controls. A spare switch clip is stored in a slot in the control housing (optional equipment). Gearshift/Throttle Control Lever CONTROL LEVER The gearshiftlthrottle control lever controls engine speed and selects F (forward), N (neutral), or R (reverse) gears. SWITCH CLIP SPARE SWITCH CLIP Moving the control lever 30" from N (neutral) selects the gear, and further movement increases engine speed. The control lever automatically locks itself in the N (neutral) position. To move the lever out of the N (neutral) position, you must squeeze the neutral release lever on the underside of the lever handle. A friction adjuster near the base of the control lever(s) adjusts the operating resistance of the control lever(s). Less friction allows easier control lever movement. More friction helps to hold a steady throttle setting while cruising. CONTROLS AND FEATURES N (NEUTRAL) GEARSHIFTRHROTTLE CONTROL LEVER CONTROLS AND FEATURES Fast Idle Lever N(neutral) The fast idle lever is only needed for starting carbureted outboard models. The BF200A and BF225A models use programmed fuel injection so, this lever will not be needed for starting. After the engine starts and if the outside temperature is below 41OF (5"C),the fast idle lever can be used to accelerate engine warm up. MAXIMUM FAST IDLE The fast idle lever will not move unless the remote control lever is in the N (neutral) position. Conversely, the remote control lever will not move unless the fast idle lever is in the lowest position. Lower the fast idle lever to the lowest position to decrease the fast idle. Panel-Mount Type Ignition Switch ON START OFF IGNITION ' SWITCH KEY \ The ignition switch controls the ignition system and starter motor. CONTROLS AND FEATURES Turning the ignition switch key to the START position operates the starter motor. The key automatically returns to the ON position when released from the START position. The ignition switch can be used to operate the starter motor only when the control lever (p. 21 ) is in the N (neutral) position, and the switch clip is in the emergency stop switch. Turning the ignition switch to the OFF position stops the engine. Switch Clip and Emergency StopSwitch EMERGENCY STOP SWITCH \ SWITCH CLIP LANYARD SWITCH CLIP The switch clip must be inserted in the emergency stop switch in order for the engine to start and run. The lanyard must be attached to the operator’s PFD (Personal Flotation Device) or worn around the wrist as shown. When used as described, the emergency stop switch and lanyard system stops the engine if the operator falls away from the controls. A spare switch clip is stored in the tool bag (optional equipment). SPARE SWITCH CLIP CONTROLS AND FEATURES Fast Idle Button N (neutral) FAST IDLE BUTTON By moving the control lever forward or reverse when the fast idle button is pushed in, the throttle opening will be increased without engaging the gears. It is necessary to position the control lever in N (neutral) to push in the fast idle button. Gearshift/Throttle Control Lever CONTROL LEVER LEVER The gearshifdthrottle control lever controls engine speed and selects F (forward), N (neutral), or R (reverse) gears. CONTROLS AND FEATURES Moving the control lever 35" from N (neutral) selects the gear, and further movement increases engine speed. The control lever automatically locks itself in the N (neutral) position. To move, the lever out of the N (neutral) position, you must squeeze the neutral release lever on the underside of the lever handle. A friction adjuster near the base of the control lever adjusts the operating resistance of the control lever. Less friction allows easier control lever movement. More friction helps to hold a steady throttle setting while cruising. N (NEUTRAL) L 35" F (FORWARD) R (REVERSE) TH MAXIMUM MAXIMUM GEARSHIFTRHROTTLE CONTROL LEVER CONTROLS AND FEATURES Top-Mount Type Ignition Switch START ON I OFF IGNITION /\ SWITCH KEY The ignition switch controls the ignition system and starter motor. Turning the ignition switch key to the Switch Clipand Emergency StopSTART position operates the starter Switch motor. The key automatically returns to the ON position when released EMERGENCY from the START position. STOP SWITCH The ignition switch can be used to operate the starter motor only when the control lever (p. 24 ) is in the N (neutral) position, and the switch clip is in the emergency stop switch. Turning the ignition switch to the OFF position stops the engine. CLIPSWITCH \ LANY...
Эта инструкция также подходит к моделям:Лодки - Outboard Motor BF200A (1.62 mb)