Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Attwood, модель 66511

Производитель: Attwood
Размер: 459.38 kb
Название файла: 69343-g-flush-cleats-4-6-inch.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


REQUIRED FOR INSTALLATION • Adjustable wrench • Sabre saw • Length of 3/8" (9.5mm) I.D. hose • Screwdriver • Cordless drill and bits • Marine sealant WARNING: To prevent personal injury, always disconnect the power source when installing or servicing this product. Always remove the boat from the water before using any power tools. LOCATION Select an installation location that meets the following criteria: • Location on vessel must be able to withstand loads specified in application section. See ABYC Reg. H-40 for details and ratings. • Location is large enough and wide enough to accommodate the entire cleat body. • Access to the underside of the vessel is necessary for both models in order to tighten the fasteners. FLUSH CLEAT TEMPLATES Figure 1 FLUSH injury and/or damage to the boat. NOTE: Before you room for the unit in the down position, 1. Use templates provided and drill four 1/4" (6.4mm) 2. Remove the supplied fasteners sealant around the edge of the 3. Align backing plate with the underside #10 machine screws, locking washers be substituted). For the 6" thru-bolt version washers and nuts (regular washers and nylock 4. Ensure the screw is long enough to provide for washers and nuts to the studs or screws and tighten. WARNING: The Flush Cleats are not to be used for towing, lifting, or beyond those listed above. Any misuse of the intended application Figure 2 1.75" (4.45cm) 1.650" (4.19cm) 1.429" (3.63cm) 1.657" (4.21cm) 4" Cut-Out Template 4.764" (12.1cm) 7/8" Radius 1" Radius 6.475" (16.45cm) 2.220" (5.64cm) 6" Cut-Out Template 2" (5.08cm) OPTIONAL If using the Thru-Bolt Version The same cut-out can 1. Place water receptacle instructions (Figure 3). The of the cleat, deck, mounting 2. Connect 3/8" inner diameter hose the bilge or to a drain fitting. Figure 3 Hose Fitting • • • Lock Washer Nut Water Receptacle (Sold Separately) • Machine Screws• Tension/Travel Adjustment Set Screw • Marine Sealant• Cut-Out Hole• Backing Plate• Thru-Bolt Flush Cleat• ATTWOOD LIMITED WARRANTY ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”) warrants to the original consumer purchaser that Attwood brand products will be free from defects in materials and workmanship under normal use and service for one year from the date of original consumer purchases. This limited warranty is not applicable if the product has been damaged by accident, improper installation, unreasonable or improper use, lack of proper maintenance, unauthorized repairs or modifications, normal wear and tear, or other causes not arising out of defects in materials or workmanship. Attwood products are warranted for use on pleasure boats. Any other use — including but not limited to commercial, racing, or non-marine use — are not covered under this warranty. Attwood’s obligation under this warranty is limited to repair of the product at Attwood’s plant or replacement of the products at Attwood’s option without expense to the original consumer purchaser. Any expenses invo...

Эта инструкция также подходит к моделям:
Лодки - 66510 (459.38 kb)
Лодки - 66512 (459.38 kb)
Лодки - 66513 (459.38 kb)
Лодки - 66514 (459.38 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории