Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
R"9#40+0)"R" Keep button-cell batteries away from children. Swallowing a button-cell battery can be fatal. ."%#76+10". • Use only a fresh battery of the required size and recommended type. • If you do not plan to use the compass for a month or more, remove the battery. Batteries can leak chemicals that can destroy electronic parts. ±"016’"±" Your compass is designed to work in a temperature range from 14° to 122°F (–10° to 50°C). If the temperature is higher or lower than this range, the display on your compass might not work. 5’672 %#.+$4#6+0)"6*’"%1/2#55 5’66+0)"6*’"6+/’"#0&"’ 5’66+0)"6*’"#.#4/ The declination is the difference between magnetic north and true north at your location. You can select any declination from 00E to 99E and 00W to 99W. To set the declination for your location, find your location on the map to the right, write down the degree number and direction (east or west) closest to that location, repeatedly press MODE to select the degree number and direction, then press ADV./ST./SPL. to set it. Then press SET.LIGHT/ STP./RST. Press BEARING. The direction digits change depending on the compass’ direction. Hold down SET.LIGHT/STP./RST. for about 2 seconds. 97B appears. Hold the compass horizontally or place it flat on a wooden table, then rotate it slowly in two complete circles. Rotate it for at least 15 seconds per revolution. Press SET.LIGHT/STP./ RST. The first digit flashes. II; ’,&° 97B ; &&° Repeatedly press MODE until JC; then the date and time appear. Then hold down SET.LIGHT/STP./ RST. for about 3 seconds. The seconds digits flash. Repeatedly press MODE to select the hour, minute, year, month, date, week or second, and 12/24 hour format. You can set the year from 2000 to 2059. When setting the seconds, press ADV./ST./SPL. to reset them to 00. Press or hold down ADV./ST./SPL. to advance through the digits or toggle between 12- or 24-hour display, then press SET/LIGHT/ STP./RST. to confirm. JK; )0)/’( JK; )0)/&& JK; (&&( Repeatedly press MODE until 7BC and the set alarm time appears. Then hold down SET.LIGHT/STP./RST. for about 3 seconds. The hour flashes. When the alarm time appears, press ADV./ ST./SPL. to toggle between alarm mode and alarm chime mode. 0&& appears when the compass is in alarm chime mode. Press or hold down ADV./ST./ SPL. to advance through the digits, then press MODE. The minute digits flash. When you have set the minutes, press SET/LIGHT/ STP./RST. to confirm. 7BC ’0((’( 7BC +0((’( 7BC +0*.’( If you do not place the compass correctly while calibrating it, ;hh appears. If this happens, start over. ;hh 19°E - 27°E 12°E 75+0)"6*’"56129#6%* 12’4#6+10 75+0)"6*’"%1/2#55 %#4’ .19"$#66’4;" +0&+%#6+10 Hold the compass with below the bezel pointing in the direction you want to read, then press BEARING. Digits showing the current direction appear. Rotate the bezel until the digits on the bezel closest to the digits on the display are aligned with . N on the bezel points to true north. When you finish using the compass, press MODE or simply wait about 70 seconds. Repeatedly press MODE until 9>H appears. The last measurement you took appears. Press SET/LIGHT/STP./RST. to reset the stopwatch, then press ADV./ST./SPL. to start it. To take a split time, press ADV./ST./SPL. while the stopwatch is running. Use a small Phillips screwdriver to remove the screws from the back of the compass, then remove the cover. Use the screwdriver to remove the screw from the battery cap, then remove the cap. If the battery is weak, the display dims and the compass’ sound becomes weak. Keep the compass dry; if it gets wet, wipe it dry immediately. Use and store the compass only in normal temperature environments. Handle the compass carefully; do not drop it. Keep the compass away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new. 4’2.#%+0)"6*’"$#66’4; Press SET/LIGHT/STP./RST. to stop the stopwatch. 75+0)"6*’"6+/’4 Repeatedly press MODE until JCH appears. The last countdown mode (9:I (countdown stop), 9:H (countdown repeat), or 9:K (countdown up)) and the last measurement you took appears. Hold down SET/LIGHT/ STP./RST. for about 3 seconds. The second digits flash. Repeatedly press ADV./ST./ SPL. to change the selected setting, then repeatedly press MODE to select the second, minute, hour, and countdown mode. Make sure the positive (+) side of the fresh battery faces up. When you finish setting the timer, press SET/LIGHT/ STP./RST. To start the timer, press ADV./ ST./SPL.To stop the timer and reload the preset time, press SET/LIGHT/STP./RST. II; ’,&° 9>H (yy(&&& ‘ 9>H &yy&&&& ‘ 9:H ’0&,&) 9:H ’0&,&) 9:H ’0&,&& 9:H (0&&&& CR2032 CR2032 MODE — Use to set the display mode. BEZEL ±"016’"±" In time display mode, press ADV./ST./SPL. to toggle between time and date. 4’5’66+0)"6*’" %1/2#55 If the compass does not work properly, reset it by pressing all buttons at the same time. 63-5027 $TOLWNC"&KIKVCN"EQP"4GNQL"FG"%NKR La brujula digital con reloj de sujetador RadioS...