Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded. Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A. Repair or replace damaged or worn cord immediately. POWER CONNECTIONS MOTOR SPECIFICATIONS Your machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position. GROUNDING INSTRUCTIONS THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Ampere Rating Volts Total Length of Cord in Feet Gauge of Extension Cord 0-6 240 up to 50 18 AWG 0-6 240 50-100 16 AWG 0-6 240 100-200 16 AWG 0-6 240 200-300 14 AWG 6-10 240 up to 50 18 AWG 6-10 240 50-100 16 AWG 6-10 240 100-200 14 AWG 6-10 240 200-300 12 AWG 10-12 240 up to 50 16 AWG 10-12 240 50-100 16 AWG 10-12 240 100-200 14 AWG 10-12 240 200-300 12 AWG 12-16 12-16 12-16 240 240 240 up to 50 50-100 14 AWG 12 AWG GREATER THAN 100 FEET NOT RECOMMENDED Fig. D-2 FUNCTIONAL DESCRIPTION FOREWORD The Delta 10” Hybrid Saw (36-714) has a powerful 13/4 HP induction motor that can handle tough cutting operations. This table saw has a maximum depth of cut of 31/8 inches (79mm) at 90 degrees and 21/8 inches (54mm) at 45 degrees. The maximum dado width with this saw is 13/16 inch (21mm). The saw comes with two cast iron extension wings, one of three fence systems, see-through blade guard and splitter, table insert, equipment mounting hooks, a 10" diameter blade, dust port for 4" hose and miter gage. NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS CONTAINED IN THE MANUAL ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED TO ILLUSTRATE TECHNIQUE ONLY. CARTON CONTENTS Fig. 1 Parts 1. Cast Iron Extension Wings (2) 2. Switch Assembly 3. Fence Holder Brackets (2) 4. Drive Belt 5. Table Insert 6. Wrench Hook 7. Miter Gage Holder 8. Splitter Mounting Bracket 9. Blade Hex Nut 10. Blade Flange 11. 10” Carbide- Tipped Blade 12. Blade Wrenches (2) 13. 4mm Hex Wrench 14. Dust Port 15. Locking Knobs (2) 16. Handwheel (2) 17. Miter Gage 18. Miter Gage Handle 19. Splitter/Guard Assembly Fig. 1 1 4 2 5 7 6 3 8 9 10 11 1213 14 15 16 17 18 19 8 Fig. 2 Parts 1. 7/16"-20 x 11/4" Hex Head Screw (6) 2. 7/16" Flat Washer (6) 3. 7/16" Lock Washer (6) 4. M8x30 Hex Head Screw (1) 5. M8 Nut (1) 6. M8 lock washer (1) 7. M8 flat washer (1) 8. M8x25 Hex Head Screw (2)* 9. M8 Washer (2)* 10. M8 Lock Washer (2)* 11. 1/4”-20x3/8” Round Head Tap Screw (8) 12. M4 x 10mm Round Head Screw (6) 13. 1/4"-20 x 3/4" Hex Head Screw (2) 1 2 9 12 11 131920 Fig. 2 5 4 3 8 141516 181721 6 7 10 14. 1/4" Flat Washer (2) 15. 1/4" Lock Washer (2) 16. 5/16"-18 x 5/8 Carriage Head Screw (1) 17. 5/16" hex nut (1) 18. 5/16" flat washer (1) 19. Nylon Washer (2) 20. M5x20mm Screw (1) 21. Washer for Miter Gage (1) * Parts 8, 9 and 10 are included to attach the rear rail of the fence to the table of this saw. UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. The basic saw unit is shown as shipped here in Fig. 2. Fig. 2 ASSEMBLY ASSEMBLY TOOLS REQUIRED * Phillips head screw driver (not supplied) * 12mm, 13mm and 18mm open end wrenches (not supplied) * Other wrenches and a drill with a 1/4 inch bit may be required, depending on what fence or tables will be used ASSEMBLY TIME ESTIMATE - 2 to 3 hours FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTI...