Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
H Saw blade TCT 315 x 2.8 x 30 48 universal alternate bevel teeth For all woods and wood-derived materials. I Roller Stand RS 420 J Roller Stand RS 420 W K Roller Stand RS 420 G 14. Environmental Protection The machine's packing can be 100% recycled. Worn out power tools and accessories contain considerable amounts of valuable raw and rubber materials, which can be recycled. These instructions are printed on paper produced with elemental chlorine-free bleaching process. 15. Trouble Shooting A A Danger! Before carrying out any fault service or maintenance work, always: 1. switch machine OFF; 2. unplug power cable; 3. wait for saw blade to come to standstill. Check that all safety devices are operational again after each fault service. Motor does not run Undervoltage relay tripped by power failure: . switch on again. No mains voltage . Check cables, plug, outlet and mains fuse. Motor overheated, e.g. by a blunt saw blade or chip build-up in the chip case: . remove cause for overheating, wait for a few minutes, then start saw again. Motor supply voltage too low: . use a shorter extension cable or extension cable with larger lead cross section (. 1.5 mm2). . Have power supply checked by a qualified electrician. Loss of cutting performance Saw blade blunt (possibly tempering marks on blade body): . replace saw blade (see chapter "Care and maintenance"). Saw dust build-up No dust collector or dust collector of insufficient capacity connected (see “Dust collector” in chapter “Operation”): . connect dust collector, or . increase suction capacity. Height adjustment mechanism of saw blade working stiff Spindle of height adjustment mechanism gummy: . clean spindle and spray with Care and Maintenance Spray (see chapter "Care and maintenance"). ENGLISH ENGLISH 16. Technical specifications TKHS 315 C 2,8 DNB TKHS 315 C 2,0 WNB TKHS 315 C Saudi Arabia Voltage 400 V / 3~50 Hz 230 V / 1~50 Hz 230 V / 1~60 Hz Nominal current A 6.6 9.3 9.4 Fuse protection min. A 3 - 10 (time-lag) 1 - 16 (time-lag) 1 - 16 (time-lag) Protection class IP 54 IP 54 IP 54 Motor speed min-1 2778 2782 3343 Motor capacity power input P1 power output P2 kW kW 2.8 kW S6 40% 2.15 kW S6 40% 2.0 kW S6 40% 1.5 kW S6 40% 2.0 S6 40% 1.45 S6 40% Saw blade cutting speed m/s 46 46 55 Saw blade diameter (outer) mm 315 315 315 Arbor bore mm 30 30 30 Depth of cut with saw blade vertical at 45° saw blade tilt mm mm 0... 85 0... 60 0... 85 0... 60 0... 85 0... 60 Dimensions length saw table width saw table length table extension width table extension height height (saw table) height (over all) mm mm mm mm mm mm 800 550 800 400 850 1050 800 550 800 400 850 1050 800 550 800 400 850 1050 Weight complete approx. kg 64.0 62.0 62.0 Sound power level according to ISO 7960* no-load when sawing Sound pressure level according to ISO 7960* no-load when sawing dB (A) dB (A) dB (A) dB (A) 89.4 100.9 75.4 86.4 89.0 100.9 75.4 86.4 91.2 102.8 77.4 87.9 Ambient temperature range ° C –10 … +40 –10 … +40 –10 … +40 Extension cable – min. lead cross section Length of cable 10 m Length of cable 25 m Length of cable 50 m mm2 mm2 mm2 5 x 1.5 5 x 2.5 5 x 2.5 3 x 1.0 3 x 1.5 3 x 2.5 3 x 1.0 3 x 1.5 3 x 2.5 * The values stated here only indicate the loudness emitted by this machine. If the operator is required to wear hearing protection cannot be determined here. This depends on how much noise reaches the ear of the operator. And this, among other things, depends on the existing ambient conditions (such as other sources of noise near by). Even though it may not be explicitly required, it is in your own interest to always wear hearing protection when operating this machine. 27 FRANCAIS 1. Fournitures a la livraison 1 2 4 5 6 10 11 12 16 15 14 13 17 18 19 7 8 3 9 1 Plaque de rallonge 2 Capot de protection 3 Tuyau d'aspiration 4 Support de tuyau 5 Butee universelle de piece a usiner 6 Plateau avec support de moteur, moteur, commutateur, lame de scie, couteau diviseur, manchon d'aspiration 7 Profile de fixation - butee parallele 8 Crochets a vis pour suspendre les accessoires (2x) 9 Poignees de transport (2x) 10 Pieds (4x) 11 Montants courts (2x) 12 Montants longs (2x) 13 Cle de changement de lame 14 Cle de changement de lame 15 Poignee pour bloc poussoir 16 Poussoir / aide d'attaque 17 Kit roulettes 18 Profile de fixation - butee transversale 19 Etais (2x) – Instructions de service et liste des pieces de rechange – Sacoche contenant les petites pieces XA0039F2.fm Instructions d'utilisation FRANCAIS 28 FRANCAIS 2. Vue d'ensemble de la scie complete 20 23 24 25 26 27 28 29 30 21 22 31 20 Rallonge de table 21 Tuyau d'aspiration 22 Capot de protection 23 Butee universelle – utilisable comme butee parallele (montage a l'avant) ou transversale (montage sur la gauche) 24 Support pour poussoir / aide d'attaque et poignee de bloc poussoir 25 Bielle de reglage en continu de la hauteur de coupe de 0 a 85 mm 26 Interrupteur "marche-arret" 27 Poignee de transport 28 Support pour les cles de changement de lam...