Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Persons under 18 years of age shall use this tool only in the course of their vocational training, under the supervision of an instructor. Do not permit other persons to touch the tool or power cable while it is running. Do not overload tool – use it only within the performance range it was designed for (see "Technical specifications"). B Danger! Risk of electric shock! Do not expose tool to rain. Do not operate tool in damp or wet environment. Prevent body contact with earthed objects such as radiators, pipes, cooking stoves, refrigerators when operating this tool. Do not use the power cable for purposes it is not intended for. A A Risk of personal injury and crushing by moving parts! Do not operate the tool without installed guards. Always keep sufficient distance to the saw blade. Use suitable feeding aids, if necessary. Keep sufficient distance to driven components when operating the electric tool. Do not attempt to stop the saw blade by pushing the workpiece against its side. Ensure the tool is disconnected from power supply before servicing. Ensure that when switching on (e.g. after servicing) no tools or loose parts are left on or in the tool. Turn power off if the tool is not used. A A Cutting hazard, even with the cutting tool at standstill! Wear gloves when changing cutting tools. A Risk of kickback (workpiece is caught by the saw blade and thrown against the operator): Always work with a properly set riving knife. Do not jam workpieces. Cut thin or thin-walled workpieces only with fine-toothed saw blades. Always use sharp saw blades. If in doubt, check workpiece for inclusion of foreign matter (e.g. nails or screws). Cut only stock of dimensions that allow for safe and secure holding while cutting. Never cut several workpieces at the same time – and also no bundles containing several individual pieces. Risk of personal injury if individual pieces are caught by the saw blade uncontrolled. When cutting round stock, use a suitable jig to prevent the workpiece from turning. c Drawing-in/trapping hazard! Ensure that no parts of the body or clothing can be caught and drawn in by rotating components (no neckties, no loose- fitting clothes; contain long hair with hair- net). Never cut workpieces containing the following materials: . ropes . strings . cords 17 ENGLISH . cables . wires AHazard generated by insufficient personal protection gear! Wear hearing protection. Wear safety glasses. Wear dust mask. Wear suitable work clothes. When working outdoors wearing of non-slip shoes is recommended. ARisk of injury by inhaling wood dust! Dust of certain timber species (e.g. oak, beech, ash) can cause cancer when inhaled: work only with a suitable dust collector attached to the saw. AHazard generated by modification of the machine or use of parts not tested and approved by the equipment manufacturer! Assemble tool in strict accordance with these instructions. Use only parts approved by the equipment manufacturer. Use only tools (saw blades) conforming to EN 847-1:1997. Do not make changes to any of the parts. Use only matching saw blades and riving knives. AHazard generated by tool defects! Keep tool and accessories in good repair. Observe the maintenance instructions. Before any use check tool for possible damage: before operating the tool all safety devices, protective guards or slightly damaged parts need to be checked for proper function as specified. Check to see that all moving parts work properly and do not jam. All parts must be correctly installed and meet all conditions necessary for the proper operation of the tool. Damaged protection devices or parts must be repaired or replaced by a qualified specialist. Have damaged switches replaced by a service centre. Do not operate tool if the switch can not be turned ON or OFF. Keep handles free of oil and grease. 3.3 Symbols used throughout these instructions ADanger! Indicates risk of personal injury or severe material damage. BRisk of electric shock! Risk of personal injury by electric shock. cDrawing-in/trapping hazard! Risk of personal injury by body parts or clothing being drawn into the rotating saw blade. A Caution! Risk of material damage. 3 Note: Additional information. 3.4 Safety devices Riving knife The riving knife (12) prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator. Always have the riving knife installed during operation. Blade guard The blade guard (13) protects against unintentional contact with the saw blade and from chips flying about. Always have the blade guard installed during operation. Push stick The push stick (14) serves as an extension of the hand and protects against accidental contact with the saw blade. Always use the push stick if the distance between saw blade and rip fence is less than 120 mm. Guide the push stick at an angle of 20° … 30° against the saw table's surface. When the push stick is not used, it can be hung to the holder (15) provided. Replace the p...