Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
EXHAUST PORT TOINSTALL BLADE See Figures 10, 11, and 12. WARNING: A 10 in. blade is the maximum A blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage withthe flats on the spindle.Larger bladeswillcome incontactwiththe blade guards, while thicker blades will prevent the blade screw from securingthe btade on the spindle. Either of these situationscould result in aseriousaccidentandcancause serious personal injury. • Unplug your saw. _ WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. Push down on the saw arm and pullout the lock pin to release saw arm. Raise saw arm to its full raised position. Be cautious, saw arm is spring loaded to raise. • Loosen the phillips screw on the blade bolt cover until blade bolt cover can be raised. See Figure lO and 11. • Gently raise the lower blade guard bracket, releasing lower blade guard from notch so that lower blade guard and blade bolt cover can be rotated up and back to expose the blade bolt. See Figures 10 and 11. PHILLIPSSCREW LOWER BLADEGUARD DUSTGUIDE LOWERBLADE GUARD BRACKET Fig. 10 Fig. 9 13 LOWER BLADEGUARD BOLTCOVER TO TIGHTEN PHILLIPS SCREW ON SPINDLE INNERBLADE WASHERW_H DOUBLE"D"FLATS BLADE :)LITERBLADEWASHER WITHDOUBLE"D" FLATS BLADEBOLT Fig. 11 • Depress the spindle lockbutton and rotatethe blade boltuntilthe spindle locks. See Figure 12. • Usingthe blade wrench provided, loosen and remove the blade bolt. Note: The blade bolt has left hand threads. Turn blade bolt clOCkwiseto loosen. • Remove outer blade washer. Do not remove inner blade washer. SPINDLE BUTTON Fig. 12 • Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade. ,_ WARNING: If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so couldcause an accident since blade wil_nottighten properly, • Fit saw blade inside lower blade guard and onto spindle.The blade teeth point downward at the front of saw as shown in figure 11. CAUTION: Always instaIJthe blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw, The direction of blade rotation is also stamped with an arrow on the upper blade guard. • Replace outer blade washer, The double "D"flats on the blade washers align with the flats on the spindle. • Depress spindle lock button and replace blade bolt. Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten. • Tighten blade bolt securely. • Remove the blade wrench and store it in a safe place for future use. • Replace the lower blade guard and blade bolt cover. • Retighten phillips screw securing blade bolt cover. Tighten screw securely. See Figure 11. _. WARNING: Make sure the spindle lock button is not engaged before reconnecting saw into power source,Neverengage spindlelockbuttonwhen blade is rotating. Your compound miter saw has been adjusted at the factory for making very accurate cuts. However, some of the components might have been jarred out of alignment duringshipping.Also,overa periodoftime, readjustmentwill probablybecome necessary due to wear. After unpackingyour saw, check the following adjustments before you begin usingsaw. Make any readjustments that are necessary and periodically check the parts alignment to make sure that your saw is cutting accurately. _. WARNING: Your saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. Disconnectingyour saw will prevent accidental starting that could cause serious injury. 14 Note: Many of the illustrations in this manual show FENCE only portions of your compound miter saw. This is MITER TABLE intentional so that we can clearly show points being made in the illustrations. Never operate your saw without all guards securely in place and in good operating condition. SQUARING THE MITER TABLE TO THE FENCE See Figures 13 -16. • Unplug your saw. _1= WARNING: Failure to unplug your saw could FRAMING ZERO CLEARANCE result in accidental starting causing possible SQUARE THROAT PLATE serious personal injury. VIEW OF MITERTABLE NOTSQUAREWITH FENCE,ADJUSTMENTSARE REQUIRED • Push down on the saw arm and pull out the lock Fig. 14 pin to release the saw arm. • Raise saw arm to its full raised position. FENCE • Loosen the miter lock handle approximately one-MITER TABLE half turn. • Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0 °. • Release the miter lock plate and securely tighten the miter lock handle. • Lay a framing square flat on the miter table. Place one leg of the square against the fence. Place the other leg of the square beside the zero clearance throat plate in the miter table. The edge of the FRAMING ZERO CLEARANCE square and the zero clearance throat plate in SQUARE THROAT PLATE the miter table should be parallel as...