Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Failure to heed this warning can result in serious personal injury. CUTTING WITH YOUR COMPOUND MITER SAW ,& WARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury. CROSSCUTTING See Figure 26. A crosscut is made by cutting across the grain of the workpiece. A straight crosscut is made with the miter table set at the zero degree position. Miter crosscuts are made with the miter table set at some angle other than zero. TO CROSSCUT WITH YOUR MITER SAW: • Pull out the lock pin and lift saw arm to its full height. • Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen. • Press the miter lock plate down with your thumb and hold. • Rotate the control arm until the pointer aligns with the desired angle on the miter scale. • Release the miter lock plate. Note: You can quickly locate 0°, 15°, 22-1/2 °, 31.62 °, and 45 ° left or right by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the positive stop notches, located in the miter table frame. • Tighten the miter lock handle securely. WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut. 19 / STRAIGHT CROSSCUT C-CLAMP Fig. 26 • Place the workpiece fiat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 33 and 34. • When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. Align cutting line on the workpiece with the edge of saw blade. Grasp the stock firmly with one hand and secure it against the fence. Use the work clamp or a C- clamp to secure the workpiece when possible. See Figure 26. ,_ WARNING: To avoid serious personal injury, keep your hands outside the no hands zone; at least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists. • Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made. • Grasp the saw handle firmly, depress the palm pad, then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed. Slowly lower the blade into and through the workpiece. See Figure 26. Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from the miter table. BEVEL CUT See Figures 27 and 28. A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the workpiece. A straight bevel cut is made with the miter table set at the zero degree position and the blade set at an angle between 0° and 45 °. LEFTSIDE RIGHTSIDE LEFT ;HT INDICATOR INDICATOR POINT POINT ! MOUNTINGBRACKET SCALE Fig. 27 TO BEVEL CUT WITH YOUR MITER SAW: • Pull out the lock pin and lift saw arm to its full height. • Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen. • Press the miter lock plate down with your thumb and hold. • Rotate the control arm until the pointer aligns with zero on the miter scale. Release the miter lock plate. Note: You can quickly locate zero by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the built-in positive stop notches, located in the miter table frame. • Tighten the miter lock handle securely. WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut. 2O BEVELCUT C-CLAMP Fig. 28 • Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle. • Bevel angles can be set from 0° to 45°. • For your convenience there is a double scale located on the mounting bracket. See Figure 27. If one side becomes difficult to read as you move the saw arm to the left, simply refer to the other side. Align the indicator point for the side you choose with the desired angle. • Once the saw arm has been set at the desired angle, securely tighten the bevel lock knob. • Place the workpiece flat on the miter table with one edge securely against the fe...