Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply. SAVE THESE INSTRUCTIONS Assembly A WARNING: Sharp blade. To prevent accidental operation, turn off and unplug saw before performing the following operations. Failure to do this could result in serious personal injury. Fitting the saw blade (fig. A) - Hold the saw blade (7) as shown, with teeth facing forward. - Push the lever (4) downwards. - Insert the shank of the saw blade into the blade holder (15) as far as it will go. - Release the lever. - Adjust the blade support roller as described below. AccuCut™ blade support roller (fig. B) After fitting the blade, you need to adjust the blade support roller (5). Screwdriver Method - Turn the slotted blade support adjustment screw (6) in direction A. - Slide the blade support roller against the rear of the blade. The blade must locate in the central recess of the roller. - Turn the blade support adjustment screw in direction B to lock the blade support in place. Tool Free Method - The blade support roller can be adjusted in a “tool free” manner, by turning the scroll ing knob (8) so that the adjustment screw is rotated around to the front of the unit where it can be turned by hand. Connecting a vacuum cleaner to the tool (fig. C & D) - Align the dust extraction adaptor (14) with the saw shoe as shown. - Insert the ribs (16) into the slots (17). - Pull the adaptor towards the rear of the jigsaw to secure. - Connect the vacuum cleaner hose (18) (not supplied) to the adaptor. - Dust extraction is not possible when making bevel cuts. A WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal filings will be hot and could cause a fire in the vacuum container. Operation A WARNING: Laceration Hazard. To prevent loss of control, never use the tool when the saw shoe is loose or removed. Failure to do this could result in serious personal injury. Adjusting the shoe plate for bevel cuts (fig. E) The shoe plate can be set to a left or right bevel angle of up to 45°. - Turn the locking knob (11) in direction A to release the shoe plate (10). - Pull the shoe plate (10) backwards and set it to the required angle. You can use the scale or a protractor to check the angle. - Turn the locking knob (11) in direction B to lock the shoe plate in place. To reset the shoe plate for straight cuts: - Turn the locking knob (11) in direction A to release the shoe plate (10). - Pull the shoe plate backwards and set it to an angle of approximately 0. - Push the shoe plate forward. - Turn the locking knob (11) in direction B to lock the shoe plate in place. Make sure that the shoe plate is supported by the guide ribs. Variable speed control - Set the variable speed control knob (3) to the required speed range. Use a high speed for wood, medium speed for aluminum and PVC and low speed for metals other than aluminum. Switching On and Off - To switch the tool on, press the on/off switch (1). - For continuous operation, press the lock-on button (2) and release the on/off switch. - To switch the tool off, release the on/off switch. To switch the tool off, when in continuous operation, press the on/off switch once more and release it. Using the mode selector The mode selector (9) can set in 3 positions 1. Scrolling position (figs F and G) - this position allows the scroller knob (8) to be rotated for intricate and accurate sawing. (In this position there is no orbital action.) It is recommended to use scroller blades when in this mode. 2. Straight cutting position (figs Ha, Hb and Hc ) this position turns off orbital action and locks the scroller knob to prevent its rotation. The scroller knob can be locked in any of 4 positions for straight cutting. Method of engagement: a. Turn the Mode Selector to the scrolling position. b. Rotate the scroller knob to the desired position (this can be any of 4 positions - the blade can point forwards, reverse, left or right). c. Turn the Mode Selector to the neutral position. (In this position the Scroller Knob cannot be turned). 3. Orbital Action Position (figs Ia, Ib and Ic) - this position switches on the orbital action for fast and efficient straight cuts. This mode can only be selected with the blade pointing forwards. Method of engagement: a. Turn the mode selector to the scrolling position. b. Rotate the scroller knob to point the blade forwards. c. Turn the Mode Selector to the orbital position. (In this position the Scroller Knob cannot be turned). How to Use the Sightline® Feature (fig. J) - Use a pencil to mark the cutting line. - Position the jigsaw over the line (19). Viewing from directly above the jigsaw the line of cut can be easily followed. Should this view be restricted for any reason, the indent (20) can be used as an alternate cutting guide. Hints for Optimum Use General - Use a high speed for w...