Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
The scroller knob can be locked in any of 4 positions for straight cutting. Method of engagement: a. Turn the Mode Selector to the scrolling position. b. Rotate the scroller knob to the desired position (this can be any of 4 positions - the blade can point forwards, reverse, left or right). c. Turn the Mode Selector to the neutral position. (In this position the Scroller Knob cannot be turned). 3. Orbital Action Position (figs Ia, Ib and Ic) - this position switches on the orbital action for fast and efficient straight cuts. This mode can only be selected with the blade pointing forwards. Method of engagement: a. Turn the mode selector to the scrolling position. b. Rotate the scroller knob to point the blade forwards. c. Turn the Mode Selector to the orbital position. (In this position the Scroller Knob cannot be turned). Operating the Laser Installing the batteries Detach the laser from the jig saw by removing the screw shown in figure J and pulling laser forward. Insert 2 fresh 1.5 volt AAA alkaline batteries making sure to match (+) and (-) terminals correctly. Reattach the laser. WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk: • Carefully follow all instructions and warnings on the battery label and package. • Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment. • Do not short battery terminals. • Do not charge batteries. • Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type. • Remove dead batteries immediately and dispose of per local codes. • Do not dispose of batteries in fire. • Keep batteries out of reach of children. • Remove batteries if the device will not be used for several months. 11 10 11 E max 6 max 6 F G Hb max 6 Hc Ib Ha Ia Ic J 15 4 7 A B C D K COMPLIES WITH 21CFR PARTS 1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO.50, DATED JULY 26,2001. 588808-01 Made in China Type 1 3V DC Use with compatible B&D Jig Saws. Pats. Pend. 1-800-54-HOW-TO Black & Decker (U.S.) Inc., Towson, MD 21286 U.S.A. LISTED 406A WARNING/ADVERTENCIA/AVERTISSEMENT To reduce the risk of injury, user must read and understand instruction manual. Use (2) AAA size alkaline batteries. A titre preventif, lire le guide. Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual de instrucciones. Utilice (2) baterias alcalinas AAA. ON/OFF For your convenience and safety, the following labels are on the laser. Pour plus de commodite et de securite, les etiquettes suivantes sont apposees sur le laser. Para su comodidad y seguridad, el laser incluye las siguientes etiquetas. Laser On/Off Button Bouton marche/arret du laser Boton de encendido/apagado del laser Screw Vis Tornillo ON OFF “Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.” On Board Laser Your saw is equipped with a removable laser which is turned on and off separately from the jig saw. Laser is compatible with JS700L jig saw. WARNING: NEVER aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator. DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the workpiece. Laser light can damage your eyes. WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool. Switching the laser On and Off To turn the laser on, press in on the button shown in figure J. To turn the laser off, press the button a second time. Adjusting the laser side to side NOTE: Laser is intended to be a cutting aid and does not guarantee a precise cut. Use laser adjustment screw shown in figure K to align laser line with saw blade if needed. WARNING: DO NOT adjust the laser when the jig saw is plugged in. WARNING: Laser circuit will reduce output visibility (power) of laser when overheated. Laser may be not visible when saw is overloaded for prolonged period of time. Laser visibility (power) will gradually return back to normal when tool cools down even if the tool is unplugged. WARNING: Do not leave overheated laser ON unattended. Make sure the switch is in the OFF position as shown in t...